Xilinx LogiCORE MicroBlaze Product Manual Download Page 33 | Manualshive

Page: 33 / 64

background image

MicroBlaze Micro Controller System v1.3

32

PG048 December 18, 2012

Chapter 5

Constraining the Core

Required Constraints

There are no required constraints for this core.

Device, Package, and Speed Grade Selections

There are no Device, Package or Speed Grade requirements for this core.

Clock Frequencies

There are no specific clock frequency requirements for this core.

Clock Management

MicroBlaze MCS is fully synchronous with all clocked elements clocked by the

Clk

input.

Clock Placement

There are no specific Clock placement requirements for this core.

Banking

There are no specific Banking rules for this core.

«
...
31
32
33
34
35
...
»

Summary of Contents for LogiCORE MicroBlaze

































































Reviews:

No comments

Related manuals for LogiCORE MicroBlaze

7000-2 - Escalade RAID Controller

Brand: 3Ware Pages: 2

Max Charge MC-624

Brand: Balmar Pages: 8

MAX CHARGE MC-614

Brand: Balmar Pages: 20

Brand: Eaton Pages: 2

Brand: S&P Pages: 12

Brand: S&C Pages: 34

Brand: S&C Pages: 32

IntelliCap Plus

Brand: S&C Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 35

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: Samson Pages: 80

Brand: Haehne Pages: 44

CURTIS DC Series

Brand: NOCO Genius Pages: 2

Brand: Xylem Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands