background image

 

HARDWARE IDENTIFICATION CHART 

 

 

 

 

 

 

WARNING LABEL(67) 

 

 

 

 

THE WARRANTY IS NOT VALID IF: 

The machine is placed outdoors or exposed to sun and dust. Keep the machine free of dust 

and fluff. 

 

 

CAUTION! 

The company does not have no responsibility for causing damage due to misuse 

of the product and non-compliance with the instructions for use. 

 

 

Check and tighten the screws at regular intervals, as they may loosen due to vibrations. 

Damage that may be caused by a lack of maintenance is not covered by the warranty. 

 

 

CAUTION!

 During exercise, heavy sweating can cause mechanical and electrical damage to the machine. Like 

any other liquid substance, sweat is capable of causing damage mainly to the electrical parts of the machine 

(dial, cables, etc.). The best solution is to use a towel during exercise, and wipe the machine after each use to 

avoid any unwanted damage.

 

 

 

 

 

 

 

 

 

This chart is provided to help identify the warning, caution, and notice labels on the 

X-FIT 2125. 

Please take a moment to familiarize yourself with all of the warning, caution, and notice labels. 

WARNING 

For consumer use only. Failure to follow all 

warnings and instructions could result in 

serious injury or death. Before assembling or 

using this product, read and follow the Owner’s 

Manual and all other warnings and instructions 

that accompany this product. Replace this 

warning label if damaged, illegible, or removed. 

Keep others including children & pets 

away from equipment when in use. 

Consult your physician before starting this or 

any exercise program. This is especially 

important if you are over the age of 35 or have 

any pre-existing health condition. Always 

make sure all nuts and bolts are securely 

tightened before using this product. This 

product should not be used by persons 

weighing more than 250 lbs. unless otherwise 

stated in your Owner’s Manual. 

Summary of Contents for 2125
























Reviews: