background image

CONTROLLER COMPONENTS AND OPTIONS

2-2

XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS

Figure 2-1.

Components of the Sun Ultra 2 workstation

1 Processor 
2 Monitor

Mouse and mouse pad

4 Keyboard
5 Diskette 

drive

6 CD-ROM 

drive

Processor

The 256 MB RAM processor is the central processing unit of the Sun 
workstation. It contains a power switch, an internal disk drive, a 
diskette drive, a CD-ROM drive, a power receptacle and outlet, 
connectors and ports.

The processor has the following components:

Internal disk drive: 

One 4.2 GB internal disk drive is provided 

as a standard feature of the processor. The operating system, 
the NPS application, and any queued print jobs are stored on 
the internal disk. This disk cannot be used to store other 
applications or data except as directed by your service 
representative. Up to three optional disk drives are available in 
increments of 4 or 9 GB.

Diskette drive: 

Diskettes inserted into a diskette drive are used 

to load files to, and back up files from, the internal disk drive. 
The diskette drive uses industry standard 3.5 inch, 1.44 MB, 
double-sided, high-density diskettes. This diskette drive is not 
an input source for print jobs nor any other data or application; it 
is reserved exclusively for use by a service representative to 
update software and to store files. The diskette drive is located 
in the processor, on the right front section for the Ultra 2.

1

3

4

2

6
5

Summary of Contents for DocuPrint 92C













































































































































Reviews: