manualshive.com logo in svg

Xerox 7700DX - Phaser Color Laser Printer, Service Manual


Share
Download
background image

Phaser 7700 Color Laser Printer Service Manual

7-197

Removal

1.

Open the right cover door.

2.

Open the front cover and lower the main lever.

3.

Lift the Accumulator Belt locking lever and pull the assembly out of the 
printer. You need to hold the locking lever up until the white nylon handle is 
exposed.

Caution

The Accumulator Belt assembly is heavy. Use the white 
nylon handle when removing the assembly from the 
printer. Do not get fingerprints on the belt.

Note

Metal tabs allow the Accumulator Belt to be laid on a flat 
surface. It can also be carried by the black handle 
located on the side.

Replacement

Note

When reinstalling the Accumulator Belt assembly the 
black handle faces the front of the printer.

Caution

Ensure that the Accumulator Belt is fully inserted or 
severe printer damage will result. 

NEVER FORCE THE 

MAIN LEVER!

Summary of Contents for 7700DX - Phaser Color Laser Printer























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7700DX - Phaser Color Laser Printer

Xerox 4520 User Manual preview
4520
Brand: Xerox Pages: 310
olympia electronics A-200 Manual preview
A-200
Brand: olympia electronics Pages: 4
WANHAO Duplicator i3 Software User Manual preview
Duplicator i3
Brand: WANHAO Pages: 24
Xerox Document WorkCentre 480cx User Manual preview
Document WorkCentre 480cx
Brand: Xerox Pages: 318
Xerox Phaser 3010 User Manual preview
Phaser 3010
Brand: Xerox Pages: 76
Xerox ColorQube 9301 Quick Manual preview
ColorQube 9301
Brand: Xerox Pages: 11
Xerox ColorQube 9303 User Manual preview
ColorQube 9303
Brand: Xerox Pages: 352
Xerox Color 560 Printer Specification Sheet preview
Color 560 Printer
Brand: Xerox Pages: 2
Xerox B1022 System Administrator Manual preview
B1022
Brand: Xerox Pages: 105
Xerox AltaLink B8145 Manual preview
AltaLink B8145
Brand: Xerox Pages: 42
Xerox AltaLink B8145 Getting Started Manual preview
AltaLink B8145
Brand: Xerox Pages: 13
Xerox D110 Manual preview
D110
Brand: Xerox Pages: 132
Xerox CopyCentre C2128 Product Safety Data Sheet preview
CopyCentre C2128
Brand: Xerox Pages: 2
Xerox Legacy 4112 User Manual Supplement preview
Legacy 4112
Brand: Xerox Pages: 20
Xerox Legacy 4112 Quick Start Manual preview
Legacy 4112
Brand: Xerox Pages: 34
Xerox 700i Specification preview
700i
Brand: Xerox Pages: 8
Xerox 4890 Advanced Troubleshooting Manual preview
4890 Advanced
Brand: Xerox Pages: 70
Xerox Legacy 4112 Specifications preview
Legacy 4112
Brand: Xerox Pages: 2

Brands by name

Popular brands

Load more brands