manualshive.com logo in svg

Xerox 7700DX - Phaser Color Laser Printer, Service Manual, Page: 121 / 406

Share
Download
Xerox 7700DX - Phaser Color Laser Printer Service Manual Download Page 121

Phaser 7700 Color Laser Printer Service Manual

3-91

Interlock Circuit Diagram

The +24 VDC Interlock Circuit 

The +24 VDC Interlock Circuit runs from the +24 VDC LVPS to the L/H Door 
Interlock Switch, the R/H Door Interlock Switch, and the Front Door Interlock 
Switch back to the Engine Control Interface Board, then into the Engine 
Control Board. Opening this circuit prevents the Laser Unit and the 
High-voltage Power Supplies from operating.

1.

With all doors closed and printer power On, check for +24 VDC between 
P535-2 of the Engine Control Interface Board and frame ground. 

2.

If +24 VDC is not present, see Troubleshooting the +24 VDC LVPS on 
page 3-90 to verify the +24 VDC LVPS is working.

3.

If working, then check the LH Cover Interlock Switch, the RH Cover 
Interlock Switch and the Front Cover Interlock Switch.

Figure 3-1  Circuit Diagram

PRINT CARTRIDGE CRUM CONNECTORS

WASTE CARTRIDGE
INTLK SW  

FRONT COVER INTLK SW  

R/H COVER INTLK SW 

LH COVER INTLK SW 

LVPS 

LVPS 

INTERFACE

BOARD

 C

 K

M

 Y

 GRY

GRY

 GRY

GRY

GRY

GRY

GRY

GRY

 ORN

 ORN

 ORN

 ORN

GRY

GRY

GRY

 VIO

 VIO

 GRY

LD

POWER

RELAY

24V

5V

P536

P537

J631

1

1

2
3

3

4
5

5

6

6

7

S7700-432

Summary of Contents for 7700DX - Phaser Color Laser Printer























































































































































































































































































































































































































Reviews:

No comments