Xerox 7700DX - Phaser Color Laser Printer, Service Manual, Page: 129 / 406

Share

Page: 129 / 406

Xerox 7700DX - Phaser Color Laser Printer Service Manual Download Page 129

Phaser 7700 Color Laser Printer Service Manual

3-99

5.

Leaving the Toner Cartridge out of the printer, run the Toner Dispense
Motor test for the system in question. Look at the far end of the Toner
Cartridge cavity and observe the Dispense Motor Gear rotate. Also, look
along the right side of the Toner Cartridge cavity. You should see the Drive
Shaft of the Toner Auger System rotate as the Toner Motor operates.

Inspect the Drive Shaft mechanism and the Motor wiring.

■

Replace the Toner Dispense Motor (RRP 29, on page 7-188) if it or its
wiring is bad.

■

Replace the Toner Dispense Base Assembly (RRP 25, on page
7-180) if the Shaft Drive mechanism is bad.

Figure 3-4 Toner Dispense Assembly

«
...
127
128
129
130
131
...
»

Summary of Contents for 7700DX - Phaser Color Laser Printer























































































































































































































































































































































































































Reviews:

No comments