manualshive.com logo in svg

Xerox 7700DX - Phaser Color Laser Printer, Service Manual, Page: 211 / 406

Share
Download
Xerox 7700DX - Phaser Color Laser Printer Service Manual Download Page 211

Phaser 7700 Color Laser Printer Service Manual

7-181

5.

Pull the shut off gate of each toner cartridge toward you (approximately 
3/4” [or 20mm]) to shut off the toner supply for each toner tube (see 
Figure 7-26, “Dispense Assembly,” on page 7-180).

Caution

Be careful when moving the stops. They are easily 
broken and may come out completely.

6.

Remove the screw holding each dispense assembly to the printer.

7.

Remove the dispense assembly by pulling both the top and bottom 
sections evenly away from the printer.

Note

The flexible tubing is not secure and can come apart 
during removal and replacement causing toner spillage.

Summary of Contents for 7700DX - Phaser Color Laser Printer























































































































































































































































































































































































































Reviews:

No comments