Xerox 2006NPC - DocuColor Color Laser Getting Started Download Page 46

Page: 46 / 114

1. Setting up the DocuColor 2006

Loading paper in the paper tray

1-36

Xerox DocuColor 2006

Pinch the Horizontal and Vertical

Paper Guides

and move them away

from the center of the tray as far as they will go.

301067B-WOL

301067b

Place the right edge of the paper stack against the right metal edge and
under the front right-hand side

paper tab

as shown below.

Ensure that the paper stack does not cover the

MAX

guideline.

301068B-WOL

301068b

To avoid jams, load paper with the long edge against the side of the tray
when possible.

6. Adjust

the

two

Paper Guides

so that they lightly touch the edges of the

paper stack.

0301101a

301102a

Summary of Contents for 2006NPC - DocuColor Color Laser



















































































































Search results

Summary of Contents for 2006NPC - DocuColor Color Laser

Reviews:

Related manuals for 2006NPC - DocuColor Color Laser

Brands by name

Popular brands

Xerox 2006NPC - DocuColor Color Laser, Getting Started

Search results

Summary of Contents for 2006NPC - DocuColor Color Laser

Reviews:

Related manuals for 2006NPC - DocuColor Color Laser

Brands by name

Popular brands