Xerox 2006NPC - DocuColor Color Laser Getting Started Download Page 84

Page: 84 / 114

1. Setting up the DocuColor 2006

Adding memory to the Printer

1-74

Xerox DocuColor 2006

Slide the panel to the left and lift to remove. The memory card slots are
located behind the panel.

301210

301211a

•

The upper slot contains the 64MB memory card, already installed

•

The lower slot is empty.

If you are replacing the 64MB memory card with one or two memory
cards, go to step 6. If you are adding another memory card to the
existing 64MB memory, perform step 5.

Remove the additional memory card from the anti-static bag.

301214a

a. Slide the card into the lower slot below the 64MB memory card.
b. Using your thumbs, press the card into the slot until it clicks.

0301063A -W O L

301233a

Go to step 7.

Summary of Contents for 2006NPC - DocuColor Color Laser



















































































































Search results

Summary of Contents for 2006NPC - DocuColor Color Laser

Reviews:

Related manuals for 2006NPC - DocuColor Color Laser

Brands by name

Popular brands

Xerox 2006NPC - DocuColor Color Laser, Getting Started

Search results

Summary of Contents for 2006NPC - DocuColor Color Laser

Reviews:

Related manuals for 2006NPC - DocuColor Color Laser

Brands by name

Popular brands