Xerox 2006NPC - DocuColor Color Laser Getting Started Download Page 14

Page: 14 / 114

1. Setting up the DocuColor 2006

Preparing for the installation

1-4

Xerox DocuColor 2006

Checking the installation components
Ensure that all of the components you ordered are available

before

you begin

the installation. All of the components are listed below.

•

Printer

•

Scanner

•

Scanner

Stand

•

Duplex Tray (optional)

•

2 Tray Module (optional)

You may need a phillips head and a flat blade screwdriver in order to
perform the installation of the DocuColor 2006.

Following the instructions ensures that the DocuColor 2006 components are
installed in the following order:
1.

2 Tray Module, if ordered

2. Printer
3.

Duplex Tray, if ordered

4. Scanner

Stand

5. Scanner
6.

Accessories, if ordered

Client Software (customer installed)

The first step

If the DocuColor 2006 was installed for you, go to

Chapter 2. Getting to know

the Xerox DocuColor 2006

If you ordered the optional 2 Tray Module, go to the

Installing the 2 Tray

Module

procedure.

If you do not have a 2 Tray Module, go to the

Upacking the Printer

procedure.

Summary of Contents for 2006NPC - DocuColor Color Laser



















































































































Search results

Summary of Contents for 2006NPC - DocuColor Color Laser

Reviews:

Related manuals for 2006NPC - DocuColor Color Laser

Brands by name

Popular brands

Xerox 2006NPC - DocuColor Color Laser, Getting Started

Search results

Summary of Contents for 2006NPC - DocuColor Color Laser

Reviews:

Related manuals for 2006NPC - DocuColor Color Laser

Brands by name

Popular brands