XCMG XE210C Operating & Maintenance Manual Download Page 37

Page: 37 / 154

XE210C Hydraulic Excavator

Operating and Maintenance Manual

Traction

Safety rules of traction

If the fault machine is not correctly pulled, or the selection and check of wire ropes are wrong, serious injury
or death will be resulted.



When the wire ropes are used, leather gloves will be
worn.



The wire ropes are fixed on a machine frame.



In the traction process, persons should not stand
between traction machine and machines which are
pulled



The machines should not be pulled on slopes.



The  wire  ropes  with  broken  wires  (A),  diameter
reduction  (B)  or  bending  (C)  should  not  be  used.  In
the  traction  process,  the  wire  ropes  may  be  broken
easily, and then, dangerous accident will be caused.

Summary of Contents for XE210C



























































































































































Search results

Summary of Contents for XE210C

Reviews:

Related manuals for XE210C

Brands by name

Popular brands

XCMG XE210C, Operating & Maintenance Manual

Search results

Summary of Contents for XE210C

Reviews:

Related manuals for XE210C

Brands by name

Popular brands