20
21
3.
Camera stops recording/does not overwrite recordings.
Check: G-SENSOR - a function by which recordings with recorded overloads
(e.g. uneven pavement, braking, driving off a kerb or over a speed bump,
etc.) are protected from being overwritten. If you use this function, you must
periodically format the memory card on your computer and then on the
camera. Ultimately, each file on the data carrier will be protected from being
overwritten and the device will not be able to record a further route - it will
not record in a loop. We suggest setting the sensor according to your driving
style and road conditions. You can also disable the option completely, in
which case each oldest file will be overwritten and the card will not need to
be formatted periodically. After adjusting the function, remember to format
the memory card.
4.
The camera switches on and off.
Check: PARKING MODE/MONITOR and MOVEMENT DETECTION - function
designed to operate while the vehicle is parked. Deactivate the functions,
before setting off, as they can cause the camera to switch on and off and
make random fragments of the route recordings. If the functions are deacti
-
vated, check if the fault occurs without a memory card inserted.
5.
The camera records sections of the route/ randomly ongoing recordings.
Check: MOVEMENT DETECTION - a function designed to operate while the
vehicle is parked. You need to deactivate the function, before setting off, as
it can cause the camera to switch on and off and make random fragments of
the route recordings. If the function is deactivated, check if the fault occurs
without a memory card inserted.
6.
The device shows the message „card full” or does not read the card.
Check the „G-sensor” and „parking mode” functions and set them to
minimum. The card must be formatted in the computer in the FAT32 or
exFAT file system (depending on the card) and then in the recorder. Check
also: Whether the selected card capacity and its specification (micro SD,
class 10 - U1, V10 additionally recommended) is suitable for your device (we
recommend using cards from reputable manufacturers, we recommend:
Kingston, Samsung, Sandisk). If at any stage you encounter an error, replace
the card with a new one from official distributors.
7.
The device records noisy, distorted, unclear sound.
The device has a highly sensitive microphone that records any ambient
noises. The recorded sounds may overlap. Windscreen air vents can also
distort the sound.
8.
The device is not responding.
Press the Reset button briefly or return the device to factory settings.
9.
There are transverse lanes in the footage.
Incorrect setting of the frame rate value. Set the frequency value to „50Hz”
or „60Hz” depending on local settings.
10.
Handle detaches from the glass/does not stick.
Degrease the surfaces well before mounting the holder on the glass.
Remember to avoid high temperatures, which can cause deformation of the
holder, and damage to the recorder itself.
NOTES:
- G-SENSOR -
a function by which recordings with recorded overloads (e.g. uneven
pavement, braking, driving off a kerb or over a speed bump, etc.) are protected
from being overwritten. If the user uses this function, you should perform periodic
formatting of the memory card in the computer and then in the camera. Because
ultimately, every file on the data carrier will be protected from being overwritten
and the device will not be able to record the further route - it will not record in a
loop. We suggest setting the sensor according to your driving style and road con
-
ditions. You can also disable this option completely, in which case each oldest file
will be overwritten and the card will not be needs to be formatted periodically.
- PARKING MODE/MONITOR -
a function designed to operate while the vehicle
is parked, uses battery power* if the DVR is fully charged - (*if it has a built-in
battery). In this case, the camera after when a shock is detected, it starts recording
a video of a few seconds - until the battery is discharged. When using this function,
bear in mind the device’s battery needs to be charged when the function activates
(starts). It should be deactivated functions, before setting off on a journey, as it
may cause the camera to switch on and off and make random fragments of route
footage.
*The constant power supply in the vehicle may cause this function to behave
differently, e.g. leaving the camera on, which may drain the car battery.
- MOVEMENT DETECTION -
a function designed to operate while the vehicle is par
-
ked - requires constant power and the camera must remain switched on. The DVR
will start recording automatically when motion is detected, and will stop recording
a few seconds after the no movement in front of the camera lens. Please note that
this function may lead to the car battery being discharged. You need to deactivate
the function, before setting off, as it can cause the camera to switch on and off and
make random fragments of route footage.
NOTE!
Use only the original charger with a charging current of 5V/1.5A. (Do not plug
directly into a 220/230V socket). Failure to follow the instructions may damage the
camera or lead to dangerous situations.
Due to continuous product improvement, the manufacturer reserves the right
to make changes to the device and its kit without prior notice. Some functions
described in this manual may differ slightly from reality.
11. SPECIFICATION
Processor:
Generalplus 6248 |
Recording resolution:
Front camera: Full HD
