Xantrex Freedom SW 815-2024 Owner'S Manual Download Page 87

Page: 87 / 96

97-0019-01-01

Troubleshooting

F57

FET1 Over Temperature

Automatic

Ambient temperature may
be too high.

Ensure adequate ventilation around the
Freedom SW.
Allow inverter to cool down and try
restarting.

Operating too large of a
load for too long while
inverting.

Remove excessive inverter loads.

Inverter cooling fan may
have failed.

If the temperature is above 104 °F (40 °C),
the fan should be on. Hold your hand or a
piece of paper to the inverter vent to check
if the fan is working.
Both fans should be active at the same
time.

Inverter airflow intake may
be blocked.

Increase the clearance around the inverter
and/or unclog the airflow intake vents.

F58

FET2 Over Temperature

Automatic

Same as

F57

Same as

F57

F63

Power Board Temp
unreadable.

Automatic Temperature

sensor

damaged.

Service required.

Table 4

Fault Messages

Fault
Number

Message

Fault Type

Cause

Solution

Freedom SW 3K2K InvChg Owners Guide.book Page 73 Wednesday, October 9, 2013 1:34 PM

Summary of Contents for Freedom SW 815-2024

































































































Search results

Summary of Contents for Freedom SW 815-2024

Reviews:

Related manuals for Freedom SW 815-2024

Brands by name

Popular brands

Xantrex Freedom SW 815-2024, Owner'S Manual

Search results

Summary of Contents for Freedom SW 815-2024

Reviews:

Related manuals for Freedom SW 815-2024

Brands by name

Popular brands