Home
/
Xantrex
/
Freedom SW 815-2024
/
Owner'S Manual

Xantrex Freedom SW 815-2024, Owner'S Manual, Page: 85 / 96

Share

70 pages before
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96

Page: 85 / 96

Xantrex Freedom SW 815-2024 Owner'S Manual Download Page 85

97-0019-01-01

71

Troubleshooting

F44

Battery Over
Temperature

Automatic

Battery temperature is over
140 °F (60 °C).
Poor battery compartment
ventilation.

Stop charging if necessary.
Check cable connections.
Check battery voltage/current and
temperature. If battery is not accepting
charge, it may need to be replaced.
Check for excessive ambient temperature
and adequate ventilation in the battery
compartment.

Automatic

BTS may be damaged.

If the unit displays a temperature of over
212 °F (100 °C), the BTS will need to be
replaced.

F47

DC Under Voltage
(Immediate)

Automatic

Immediate battery under
voltage fault.

Check battery condition (short or open
cells) and ensure correct voltage.
Battery state charge or capacity is so low
that the DC voltage collapses when
inverter load is applied.
Inverter load is so large that the DC
voltage collapses when inverter load is
applied.

Table 4

Fault Messages

Fault
Number

Message

Fault Type

Cause

Solution

Freedom SW 3K2K InvChg Owners Guide.book Page 71 Wednesday, October 9, 2013 1:34 PM

«
...
83
84
85
86
87
...
»

Summary of Contents for Freedom SW 815-2024

































































































Reviews:

No comments