Xantrex Freedom SW 815-2024 Owner'S Manual Download Page 33

Page: 33 / 96

97-0019-01-01

Operating the Freedom SW with the SCP

Select Device Screen

As mentioned, this screen appears when the

Enter

button is pressed from the System Status screen. It lists all Xanbus-enabled
devices including options to select System Settings and Clock.

To display the Select Device menu:

◆

While viewing the

System Status

screen, press

Enter

Device Setup Screen

The Device Setup screen is shown when a Xanbus-

enabled component is selected from the Select Device screen. For example,
below is an example of a Device screen for the Freedom SW 3012 inverter/
charger.

Device Setup

menus display status information and changeable

settings. Changeable settings are identified by the square brackets [ ] around
values in the right-hand column.

To display the Setup menu for a device:

◆

Highlight the device name on the

Select Device

menu screen and

press

Enter

-Or-
From the device

Home

screen, press

Enter

Figure 8

Freedom SW Select Device Screen

Xanbus System Control Panel (SCP)

FGA: 809 -092 1

AC In/Charge

Inverter On

Low Battery

Fault

STBY/ON
Fault Clear

Enter

Func

System Status

Battery
BatLev
Load
AC In

12.1V -257A 84

”

Invert

120V 12A

0V 0A

EnInv

EnChg Shr

Select Device

System Settings

FSW3012 00
XAGS 00
XSCP

Press

Enter

button to go to the

Select Device menu screen.

Figure 9

Freedom SW Device Screen

Xanbus System Control Panel (SCP)

FGA: 809 -092 1

AC In/Charge

Inverter On

Low Battery

Fault

STBY/ON
Fault Clear

Enter

Func

FSW3012 00: Setup

Mode
Battery
Load
AC In

Invert

13.4V 0.0A N/A

115W 120V 12A
120V 15A 60Hz

FSW3012 00: Setup

Mode
Battery
Load
AC In

Invert

11.8V -88.0A N/A

900W 120V 7A

0V 0A 0Hz

Freedom SW 3K2K InvChg Owners Guide.book Page 19 Wednesday, October 9, 2013 1:34 PM

Summary of Contents for Freedom SW 815-2024

































































































Search results

Summary of Contents for Freedom SW 815-2024

Reviews:

Related manuals for Freedom SW 815-2024

Brands by name

Popular brands

Xantrex Freedom SW 815-2024, Owner'S Manual

Search results

Summary of Contents for Freedom SW 815-2024

Reviews:

Related manuals for Freedom SW 815-2024

Brands by name

Popular brands