Xantrex Freedom SW 815-2024 Owner'S Manual Download Page 21

Page: 21 / 96

97-0019-01-01

System Components

The Xanbus-enabled designation (see below) means that this product works
on a Xanbus network. Xanbus-enabled products are:
•

Simple to operate and routine tasks are automated.

•

Controlled by software that eliminates analog signalling errors.

•

Less susceptible to interference and line loss.

•

Upgradable through new software releases.

For detailed instructions and a complete list of Xanbus-enabled devices,
visit

www.xantrex.com.

Xanbus-enabled Products and Accessories

Product/Accessory (Not Shown)

Product Number/s

Freedom SW On/Off Switch

808-9002

GFCI receptacles

808-9003

Drip shields

808-9004

Stacking cable

808-9005

Product/Accessory (Shown above)

Product Number/s

Freedom Sequence Intelligent Power Manager

809-0912 / 809-0913

Xanbus System Control Panel (SCP)

809-0921

Xanbus Automatic Generator Start (AGS)

809-0915

3-ft network cable (0.9 m)

809-0935

25-ft network cable (7.6 m)

809-0940

75-ft network cable (22.9 m)

809-0942

Inverter drip shield

808-9004

Xanbus System Control Panel (SCP)

FG A: 809-0921

AC In/Charge

Inverter On

Low Battery

Fault

STBY/ON
Fault Clear

Enter

Func

Freedom
Sequence

SCP

AGS

25-ft cable

75-ft cable

3-ft cable

Inverter drip shield

Freedom SW 3K2K InvChg Owners Guide.book Page 7 Wednesday, October 9, 2013 1:34 PM

Summary of Contents for Freedom SW 815-2024

































































































Search results

Summary of Contents for Freedom SW 815-2024

Reviews:

Xantrex Freedom SW 815-2024, Owner'S Manual, Page: 21 / 96

Search results

Summary of Contents for Freedom SW 815-2024

Reviews: