background image

6

Smart Pad

3

5. Press 

DELAY

.  DELAY LED will flash.  Press 

DELAY once again

 to enter a 1 second delay.  (The

1 second delay allows some time for the AM/FM receiver to power up to be sure it will execute the CD
source command).

6. Press 

CNCL

 to return to SEQ mode.

7. Point the AM/FM receiver remote at IR window and press it's CD1 (source) button.

8. When the CD1 code is learned, the SEQ LED will flash then go steady when you release the CD1 key

on the remote.

9. Press 

CNCL

 

twice

 to leave the sequence mode.

You can now test the learned commands. But first, be sure the AM/FM receiver's Power is turned OFF and
the emitters are placed on each of the components as shown in 

Fig. 3

.  Now press the 

CD1

 button. The AM/

FM receiver should turn ON and it's source selector should switch to the CD1 position.

Using the same procedure, program the remaining source buttons.  Just be sure to press the correct source
button in steps 2 & 7 above.  As you complete each source (bank) button, test it before going on. Repeat
the procedure, as necessary, until correct operation is obtained.

When the 

source

 buttons are complete, proceed to program each of the 20 

function

 buttons as follows:

1. First, press 

CD1

 to select the CD1 bank.  The  functions that apply to this source (bank) will now be

"taught" (programmed) into the applicable function buttons.

2. Press 

PGM

. The PGM LED will flash.

3. Press   (play) button.  The PGM LED will come on steady.

4. Point the CD1 (CD player) handheld remote at the IR window and press it's   (play) button.

5. When the code is learned, the PGM LED will flash again, indicating it is ready to learn a command at

another button.

6. Press 

 (reverse scan) button. The PGM LED will come on steady.

7. Point the CD1 remote at the IR window and press it's 

 (reverse scan) button.

8. When the code is learned, the PGM LED will flash again, indicating it is ready to learn a command at

another button.

9. Using this same procedure, program all the remaining commands that are applicable to the CD1 as

follows: 

( forward scan), 

 (reverse skip), 

 (forward skip),    (pause),   (stop), 

RANDOM

DISC

,

and

DISC

+

).

10. When finished, press 

CNCL

 to leave the PGM mode.

At this point, check all commands to see that they operate correctly.  Reprogram as necessary.

Fig. 4  

Programming Source & Function Buttons

CLR MEM

RESTORE

NETWORK

PGM

TRNS

XFER

ERR

CNCL

FULL

DEL

EDIT

DELAY

SEQ

IR

STEP

C
O
M

B A 9 8 7 6

5

4

3

2

1

0

F

E

D

C

PROTECT

WRITE

NETWORK

ADDRESS

RANDOM

A/B

DISC

DISC

+

TAPE

TUNER

CD 1

CD 2

OFF

VOL

VOL

TNR

TNR

A M / F M

MUTE

11. Next, press 

CD2

 to select the CD2 bank. Program the 2nd CD

player's commands into the 

function

 buttons, using the same

procedure as above.

NOTE:

  In this example, it is assumed that the 2nd CD player

is a different brand so that the IR commands of the 2 players
do not interact with each other.

12. Next, press 

TUNER

 to select the tuner bank.  In this case,

there are only 3 functions that relate directly to tuner opera-
tion; 

TNR

,

TNR

(up and down tuning - usually the selection of preset

stations) and 

AM/FM

 (selection of the AM or FM band).

Program these 

function 

buttons from the AM/FM receiver's

remote, using the same procedures as above.

Summary of Contents for SMRTP3





























Reviews: