background image

 

 

 

   

 

13 

Auxiliary Power Connector (AUX POWER OUT) – D5RH and D5SH, D5SH4 

For wire runs over 150’, it is recommended to run an additional 16 AWG/2-conductor wire from the 
head-end location to the Amplified Keypad locations. This will allow the AUX POWER OUT terminals 
to supply additional power to the Amplifier Keypads to compensate for the additional distance. For 
wire runs over 300’, 16 AWG/2 conductor wire is required. The maximum wire run using CAT-5 and 
16 AWG/2-conductor is 600’. Make all connections between the D5RH and the D5KP Amplifier 
Keypad as previously described, then make the aux power connections described below. 
 
To make connections: 

1

 

Ensure that system power is OFF! 

2

 

Strip the ends of the 16 AWG wire 1/4" on both ends of the wire run. 

3

 

Remove the terminal strip from the AUX POWER OUT connector on the D5RH or D5SH, D5SH4. 

4

 

Loosen the screws for the appropriate zone’s terminal pairs on the terminal strip. 

5

 

Insert the wires into the terminal strip, paying close attention to polarity (+/-). 

6

 

Tighten the screws on the terminal strip. 

7

 

Remove the terminal strip from the PWR IN connector of the D5KP. 

8

 

Loosen the screws on the D5KP’s PWR IN terminal. 

9

 

Insert the wires into the terminal, paying close attention to polarity (+/-). 

10

 

Tighten the screws on the D5KP’s PWR IN terminal. 

11

 

Connect the terminal strip back onto the AUX POWER OUT connector on the D5RH or D5SH, 
D5SH4. 

 

 

 

Figure 3.1: AUX POWER OUT Connections on D5SH and D5RH 

 

 

Summary of Contents for D5KP

























Reviews: