background image

Indication 

 

The alarm will emit 2 sets of 
four quick beeps every 5.8 
seconds. 

 

The LED will flash red 
during the audible signal. 

 

The LCD will display ―---,‖ 
―PAS,‖ the peak CO 
concentration recorded since 
the previous reset, and 
finally ―0.‖ 

 

After testing, the alarm will 
automatically enter standby 
mode.   

 

The initiatingunit will beep 
continuously with the LED 
flashing red. 

 

Other interconnected alarms in the 
network will receive the signal 
after 5 seconds, then they will 
beep continuously with theLED 
flashing red and green 
successively. Release the 
Test/Silence button on the 
initiating unit and all the units 
will stop testing.   

 

The units testing should be 
completed within 3 minutes. 

 

After testing, the units will 
automatically enter standby mode. 

 

NOTE: 

The test function accurately tests the alarm’s CO sensing circuit without the 

need totest

 with CO

. If your CO alarm fails to emit an audible test signal, refer to the 

troubleshooting guide at the end of this manual immediately.   

 

Peak CO Concentration Memory and Reset 

 

The peak CO concentration feature is helpful in identifying if there have been any 
dangerous CO readings since a peak CO concentration reset.   
 
Each time you push the test button, the LCD displays the peak CO concentration 
recorded since the previous reset. The peak CO concentration will be displayed for 5 
seconds, and then the device will enter standby mode. In the example, 300 ppm was 
the maximum CO concentration recorded since the unit was last reset.     

 

Peak CO Concentration Reset: 

During the 5 seconds when the LCD displays the 

peak CO concentration, press and hold the test button for 3 seconds, the device will 
beep, the LED will flash green, and the peak CO concentration will be reset with LCD 
displaying ―0.‖ 

NOTE: If the carbon monoxide concentration is lower than 30 ppm, it will not be 

Summary of Contents for XC01-WR























Reviews: