background image

Alarm Mode 

X-Sense Link

+

 wireless interlinked alarms can be interconnected such that any unit that senses dangerwill cause all other 

units in the interconnected network to alarm.   

 

1.

 

If the Initiating Unit Is Triggered by CO: 

When one CO alarm is triggered in the interconnected network, the unit will beep 4 times every 5.8 seconds, paired with 

a red LED flashing indicator. Any other CO03D-W units in the network will follow suit

they will beep 4 times every 

5.8 seconds, paired with a red LED that flashes 4 times first, followed by a green LED that flashes once with every beep. 

When the CO concentration level drops below the alarm threshold, the alarm will cease.  

 

2.

 

If the Initiating Unit Is Triggered by Smoke: 

When one smoke alarm is triggered in the interconnected network, the unit will beep 3 times, paired with a red LED that 

flashes every 1.5 seconds. Any other CO03D-W units will follow suit

they will beep 3 times every 1.5 seconds, paired 

with red and green LEDs flashing in succession. 

 

NOTES 

 

When one unit is triggered, other interconnected units will sound. If the smoke alarm and CO alarm are triggered in 

the network at the same time, the alarm signal of the smoke alarm will take priority over that of the CO alarm.   

 

This alarm has a relay function that extends the wireless interconnected network for wide detection coverage. 

 

Silence Mode 

Press the test button during an alarm to make the unit enter silence mode. If the CO concentration still exceeds the alarm 

threshold, the unit will enter another alarm state. Otherwise, the unit will exit the silence mode after 9 minutes and 

resume normal operation. If the CO concentration is above 300 ppm, the silence function cannot be enabled.   

 

NOTES 

 

You can silence all interconnected units by pressing the TEST/HUSH button on one of the units. If one unit is still 

alarming, it is the initiating unit (the unit that detected danger); to silence all interlinked units, you must also press 

the TEST/HUSH button on the initiating unit. 

 

While interconnected, the initiating unit cannot be triggered again during the 9-minute silence duration. However, 

all other interconnected units can be triggered again if they detect danger during the silence mode. 

 

Technical Specifications 

Power Supply 

3 × 1.5 V AA batteries 

Product Lifespan 

About 10 years 

Sensor Type 

Electrochemical 

Safety Standard 

UL 2034 

Operating Temperature

 

40 to 100°F (4.4 to 37.8°C) 

Summary of Contents for Link+ CO03D-W




















Reviews: