background image

Test all 

interconne

cted units 

 

The red LED indicator flashes 

rapidly. 

 

Continuous 

beeping until 

you release the 

TEST/HUSH 

button. 

 

Initiatingunit. 

Hold down the TEST/HUSH 

button on one unit in the 

network.   

 

The red and green LEDsflash 

sequentially. 

Other interconnected alarms 

in the network. 

Silence Mode 

 

 

The red LED indicator flashes 4 

times every 5.8 seconds. 

 

 

None. 

CO silence mode: After 9 

minutes, the unit will exit 

silence mode.

 

 

The yellow LED indicator flashes 

once every 60 seconds. 

None. 

Silence mode during low 

battery: After 10 hours, the 

unit will exit silence mode. 

 

The yellow LED indicator flashes 

3 times every 60 seconds.

 

None. 

Silence mode during the 

end of the cycle: After 22 

hours, the unit will exit 

silence mode. 

 

The green LED indicator flashes 3 

times.

 

None. 

Exiting silence mode. 

Low Battery 

 

 

 

Display alternates between "Lb" 

and the current CO level. The 

yellowLED indicator flashesonce 

every 60 seconds. 

1 quick beep 

every 60 

seconds. 

 

The batterymust be replaced 

immediately. 

 

Fault 

 

The yellow LED indicator flashes 

twice every 60 seconds. 

2 beeps 

every 60 

seconds. 

 

Please clean youralarm 

and see if it is working 

normally. If "Err" 

continues 

to display, the unit has 

malfunctioned and must 

be replaced immediately. 

End of Life 

 

The yellow LED indicator flashes 3 

times every 60 seconds. 

 

3 quick 

beepsevery 60 

seconds. 

Replace the 

unitimmediately. 

 

Summary of Contents for Link+ CO03D-W




















Reviews: