16
X903
INSTRUCTIONS FOR USE
VISOR (XFS-03)
1
DISASSEMBLING THE VISOR
1.1 Open the visor completely (Fig.1).
1.2 Act simultaneously on both sides of the helmet, then use a finger to completely
push the release lever of the side mechanism downwards (Fig.2) and push the
visor away from the helmet using the finger (Fig.3).
2
ASSEMBLING THE VISOR
2.1 Position the left side part of the visor on the corresponding side mechanism so
that the pin inside the visor is magnetically attracted by the central seat of the
mechanism (Fig.4).
2.2 Rotate the visor up to its maximum opening position so that all internal side pins
fully enter into their seats and so that there occurs the click indicating complete
hooking of the left side of the visor to the mechanism (Fig.1).
2.3 Follow the previous operations on the right side of the helmet.
2.4 Slightly press both side parts of the visor to ensure that the automatic hooking fully
occurred.
2.5 Close the visor completely.
WARNING
-
Make sure that the mechanisms are working properly. Open and close the visor,
making sure that the mechanisms hold it in the different positions. If necessary,
repeat the above-mentioned operations.
-
Do not use the helmet if the visor has not been assembled properly.
-
Do not
remove the side mechanisms from the shell.
-
Should any of the side mechanisms fail or be damaged, please contact a Nolan-
group authorized dealer.
WARNING
The side mechanisms and the visor have some magnets: we recommend
that you read the specific warnings and precautions for use indicated in the
instructions label attached hereto.
(Available as standard or accessory/spare part)
1
ASSEMBLING THE PINLOCK
®
INNER VISOR
1.1 Disassemble the visor (see instructions above).
1.2 Ensure that the inner surface of the visor is clean and ensure that the pin adjust-
ment external levers are turned inwards (Fig.5).
1.3 Place the PINLOCK
®
inner visor on the visor.
The silicone-sealed profile of the PINLOCK
®
inner visor must be in contact with
the inner surface of the visor.
1.4 Insert one side of the PINLOCK
®
inner visor onto one of the visor pins and hold it
in position (Fig.6).
1.5 Widen the visor and fasten the other side of the PINLOCK
®
inner visor to the other
pin (Fig.7).
1.6 Release the visor.
1.7 Remove the protective film from the PINLOCK
®
inner visor and check that the
entire silicone-sealed profile of the inner visor adheres to the visor.
1.8 Fix the visor onto the helmet (see instructions above).
2
CHECKING AND ADJUSTING THE PINLOCK
®
INNER VISOR STRETCH
Check the correct PINLOCK
®
inner visor assembly by opening and closing the visor
and ensuring that they do not move with respect to each other.
Should the PINLOCK
®
inner visor not be tightly fixed to the visor, simultaneously move
both external adjustment levers upwards, to increase the stretch gradually and not
excessively (Fig.5).
The maximum stretch is achieved when the pin adjustment external levers are turned
outwards.
WARNING
-
The presence of dust between the two visors may produce scratches on both
surfaces.
-
Scratched PINLOCK
®
visors and inner visors may cause reduced visibility and
must therefore be replaced.
-
Regularly check the correct stretch of the PINLOCK
®
inner visor to prevent it from
moving and scratching both surfaces.
-
If the helmet visor fogs up and/or condensation forms between the visors, check
that the PINLOCK
®
inner visor is both correctly assembled and stretched.
-
An excessive and early stretch of the PINLOCK
®
inner visor may result in exces-
sive adherence against the visor surface and/or permanent deformations with
subsequent inability to correctly perform any following adjustments.
-
Intense sweating/breathing, the use under particular weather conditions (low tem-
peratures, high humidity, sudden changes in temperature or heavy rain) or intense
and prolonged use may affect the performance of the PINLOCK
®
inner visor and
cause fogging or formation of condensation. In such cases, to restore the sys-
tem efficiency after using the helmet, remove the PINLOCK
®
inner visor from the
helmet visor and let it dry with dry and warm air. The same procedure must be
applied to the helmet, in order to dry out humidity in case it has formed up as a
consequence of the conditions described above.
3
DISASSEMBLING THE PINLOCK
®
INNER VISOR
3.1 Remove the visor equipped with the PINLOCK
®
inner visor (see instructions
above).
3.2 Widen the visor and release the PINLOCK
®
inner visor from the pins (Fig.7).
3.3 Release the visor.
4
MAINTENANCE AND CLEANING OF THE PINLOCK
®
INNER VISOR
4.1 Remove the PINLOCK
®
inner visor from the visor. Using a damp and soft cloth,
gently clean it with neutral liquid soap. Remove the soap under running water.
4.2 Dry the visor with dry and warm air without wiping it.
Summary of Contents for LIX9U0003740299
