9
Technical Support: [email protected] US: +866 677 0053 EU: +44 (0) 1793 230 343
B
AS
IC R
E
M
O
TE CONTR
OL AN
D ADV
AN
CE
D R
E
M
O
TE CONTR
OL
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
0x1d 0x0d
0x1b 0x15
0x12 0x08
0x55 0x4a
0x06 0x03
0x07 0x02
0x44 0x51
0x1e 0x1a
The MX-0808-HDBT features a simple but intuitive IR ‘Call Back’
system of control through which the matrix is able to detect and
distinguish where the remote handset is being used to allow
sources or displays to be switched accordingly. As such, the
function of handset buttons and operation differs depending on
the user’s location.
Remote Control at the Matrix end (locally)
previous / next buttons
When using the remote control locally, i.e. pointed directly at the
matrix, the
previous / next buttons
are used to scroll between
the input sources connected to the matrix for each individual
output display. So for example, using the
previous / next
buttons
for 1 allows you to select the source to be set to display
1manually. See below.
Matrix System Code Switch
In the event that two MX-0808-HDBT units are used side by side
in the rack, the matrix is capable of switching between two distinct
IR System Codes to allow control of either matrix individually via
the handset.
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
System Code Switch
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
The default System setting is 0x00 but pressing the S
YSTEM
CODE
button on the handset
THREE TIMES
rapidly activates
the alternative Matrix
SYSTEM CODE
0x4e, allowing control of
the second unit. Pressing the button three times again to reverts
back to default 0x00 setting.
Please note:
changing the System Code is only necessary if you
are using two identical units within close range of the IR signal. If
using in different parts of the same room it is likely that you will
not need to change the setting.
Remote control at the Display end (remotely)
When controlling the matrix remotely from the display side, the
matrix automatically detects which particular output location the
user is in and only allows the selection of sources 1-8 for that
location using the button. The right hand button will be
deactivated.
For example, if you are in the Master Bedroom with a display
connected to output 3 of the matrix, the output zone is
automatically detected so options 1-8 will correspond to sources
1-8 on the matrix. Press 1-8 to scroll through your options
as you would channels on a regular TV remote.
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
11. Basic Remote Control
12. Advanced Remote
Control
IR Call Back and Third Party Control systems
Please note, due to the differing method of control based on
location, if you are using a
third party control system
, learning
the control from the IR is
NOT
recommended as control will be
limited to scrolling up/down between inputs. For discrete source
selection you will need to import discrete hex codes for control
systems. These can be obtained through the Wyrestorm website, by
contacting our technical support or you can input them manually.
IR Call Back and Third Party Control systems
For reference:
The IR is NEC and possesses a carrier wave of
38KHz with a system code of
0x00
OUTPUT
CHANNEL
INPUT SELECT
1
2
3
4
5
6
7
8
To change handset battery
Pinch here and pull out
Install battery ‘
+
’ side
up and only use
CR
2025 3V
batteries. Slide
compartment back into
the handset.
