10
Technical Support: [email protected] US: +866 677 0053 EU: +44 (0) 1793 230 343
ADV
AN
CE
D OPE
RA
TI
ON
13. Advanced Operation
Index
EDID Mode
Details
1
Full copy
Copy HDMI output’s EDID to
the specified input port
2
Limited copy
Limited copy HDMI output’s
EDID to the specified input
port
3
Fixed 1080P-2CH
Fix EDID-1080p stereo
4
Fixed 1080P-6CH
Fix EDID-1080p 5.1 Audio
5
Fixed 1080P-8CH
Fix EDID-1080p 7.1 Audio
6
Fixed 1080i-2CH
Fix EDID-1080i stereo
Typically, unless problems with device communication through
the matrix are encountered, basic operation is all that is required.
However, the following information on advanced operation will
detail how matrix system settings can be altered or data manually
input should such problems arise.
Setting Menu
Setting mode offers 5 sub-menus to choose from:
• EDID
• LC (Long Cable Mode)
• IR (Infrared)
• EQ (Equaliser)
• RST (Factory Reset)
switch
save
observe
preview
setting
A
C
MS
EQ
M1
M2
M3
EDID Mode
The EDID Mode has 6 options available to encourage device
communication
.
1.
If the matrix is unable to automatically read the EDID from
an input device or display, the selection of
full copy
, together
with your chosen
output
and
input number
, will enable the
matrix to copy EDID from one device to the other to actively
force
HDCP compatibility
between them.
For example: if output 3 is selected, followed by
input 8, the EDID from output 3 will be copied to input
8.
2.
As above, but the selection of
Limited Copy excludes
Deep Colour
from the EDID to avoid discrepancies in colour
between input and output. This can be useful if the display
still shows signs of ‘noise’ or interference. The exclusion of
Deep Colour from the EDID reduces bandwidth to allow the
signal to pass through the switch easier.
Output1 source select key code:
0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87
Output2 source select key code:
0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97
Output3 source select key code:
0xa0 0xa1 0xa2 0xa3 0xa4 0xa5 0xa6 0xa7
Output4 source select key code:
0xb0 0xb1 0xb2 0xb3 0xb4 0xb5 0xb6 0xb7
Output5 source select key code:
0xc0 0xc1 0xc2 0xc3 0xc4 0xc5 0xc6 0xc7
Output6 source select key code:
0xd0 0xd1 0xd2 0xd3 0xd4 0xd5 0xd6 0xd7
Output7 source select key code:
0xe0 0xe1 0xe2 0xe3 0xe4 0xe5 0xe6 0xe7
Output8 source select key code:
0xf0 0xf1 0xf2 0xf3 0xf4 0xf5 0xf6 0xf7
For your preference to take effect, choose EDID mode 1-6 and
press:
Follow the Tips on the right hand side and select your
output
port
and
input
port – confirmation of port selection will appear in the
bottom right. Press OK to confirm your EDID selection – the new
setting will become active on next start-up of the matrix.
CPY
On selection of a mode, a warning screen will flash up to confirm
the change made will effective from the next power up. ‘Click OK’
