background image

Concrete Vibrator, Backpack Model WBP50

Page 16 

March 2014

TROUBLESHOOTING

Engine Will Not Start

Possible Cause

Correction

Check control 

positions .

Fuel valve OFF . 

Move lever to ON 

position .

Choke open .

Move lever to CLOSED 

position unless the 

engine is warm .

Engine switch OFF . 

Turn engine switch to 

ON position .

Check engine oil level .

Engine oil level low (Oil 

Alert stops engine) .

Fill with the 

recommended oil 

to the proper level . 

See 

“Engine Oil” on 

page 12

 .

Check throttle wire .

Throttle wire nipple is 

not engaged .

Verify that the throttle 

wire is engaged . See 

“Check the Throttle 

Lever” on page 7

 .

Check throttle position Throttle is in STOP 

position

Move throttle to SLOW 

position . See 

“Setting 

the Engine Speed” on 

page 8

 .

Check fuel .

Out of fuel .

Refuel . See 

“Refueling” 

on page 11

 .

Bad fuel; engine stored 

without treating or 

draining gasoline, 

or refueled with bad 

gasoline .

Drain fuel tank and 

carburetor . See 

“Draining the Fuel 

Tank and Carburetor” 

on page 15

 . Refuel 

with fresh gasoline . 

See 

“Refueling” on 

page 11

 .

Remove and inspect 

spark plug .

Spark plug faulty, 

fouled, or improperly 

gapped .

Gap or replace spark 

plug . See 

“Spark Plug” 

on page 13

 .

Spark plug wet with 

fuel (flooded engine .)

Dry and reinstall 

the spark plug . Start 

the engine with the 

throttle lever in the 

MAX . position .

Take engine to an 

authorized Honda 

servicing dealer, or 

refer to the Owner’s 

Manual .

Fuel filter restricted, 

carburetor 

malfunction, ignition 

malfunction, valves 

stuck .

Replace or repair faulty 

components .

Engine Lacks 

Power

Possible Cause

Correction

Check air filter .

Filter element 

restricted .

Clean or replace filter element . 

See 

“Air Cleaner” on page 13

 .

Check fuel .

Bad fuel; engine 

stored without 

treating or draining 

gasoline, or refueled 

with bad gasoline .

Drain fuel tank and carburetor .  

See 

“Draining the Fuel Tank 

and Carburetor” on page 15

 . 

Refuel with fresh gasoline . See 

“Refueling” on page 11

 .

Take engine to 

an authorized 

Honda 

servicing 

dealer, or refer 

to the Owner’s 

Manual .

Fuel filter restricted, 

carburetor 

malfunction, ignition 

malfunction, valves 

stuck .

Replace or repair faulty 

components .

Check engine 

governor screw

Throttle cannot fully 

open

Back off the engine governor 

screw . See 

“Setting the Engine 

Speed” on page 8

 .

SERVICE

Repair or replacement parts can be ordered from Wyco 

Tool . Warranty repairs or chargeable repairs can be made 

by sending the product to the following address . Always 

obtain an RA number (Return Authorization) and include 

it in the address before returning any parts for warranty 

consideration or chargeable repair .
Phone: (262) 639-6770 or Toll free: (800) 233-9926
RA#
Wyco Tool 

8635 Washington Avenue 

Racine, Wisconsin 53406-3738
Engine parts may be obtained from your local Honda engine 

dealer found at 

www.engines.honda.com

 or Honda Customer 

Relations at 770-497-6400 .

PARTS

Honda Engine Parts

When Wyco part numbers are listed, the parts are available 

directly from Wyco .

Honda Engine Warranty

Go to 

http://engines.honda.com/parts-and-support/warranty-

info

Wyco Warranty

Go to 

http://wycotool.com/manuals

Wyco Drawings

Description

Drawing #

Backpack assembly

W402535

Frame assembly

W402530

Speed increaser assembly

W402600

Replacement clutch kit

W402316

Quick disconnect adapter

W402630

Summary of Contents for WBP50

























Reviews: