manualshive.com logo in svg

Wright Manufacturing Stander ZK Series, Instruction Manual, Page: 30 / 44

Share
Download
Wright Manufacturing Stander ZK Series Instruction Manual Download Page 30

30 

 

   

 

WARNING

 

   

 

WARNING

 

   

 

WARNING

 

6.13 Cutting Blades

 

In order to maintain the best cut, it is important that the blades are well sharpened and not damaged.  Bent 
or cracked blades or blades with large nicks need to be replaced.  Blades must be balanced after 
sharpening.  To change the blades: 

 Stop engine, remove the key and wait for all moving parts to stop. 

 Engage the parking brake 

 Lift front of mower and secure in the raised position with jack stands. 

 Remove the blade bolt by turning counterclockwise. 

 Apply anti-seize to the blade bolt. 

 Install new or re-sharpened blade, start mounting bolt by hand. (Ensure the blade spacers are 

reinstalled with the same qty and location) 

 Torque blade bolt to 70-80 ft/lbs / 95-108 Nm 

 

6.13 Spindle Pulley Split hub R&R 

 

Remove 2, ¼” bolts from split hub and install in threaded holes in hub. 

  Slowly tighten each bolt, alternating as you tighten bolts against the pulley. 

  The hub will separate from the pulley. 

  Replace grade 8 bolts and install in reverse order using the assembly holes to tighten hub onto pulley and 

spindle shaft. 

 
 
 
 
 
 
 
 
 
 

6.15 Loading and Unloading 

Use extreme caution when loading and unloading units on/off trailers or trucks.  One full width ramp that 
extends beyond the rear tires is recommended rather than individual ramps for each side of the unit.  The 
ramp should be long enough so that the angles between the ramp and the trailer or truck does not exceed 
15 degrees.  A steeper angle may cause the mower deck components to get caught as the unit moves 
from ramp to trailer or truck.  Always put the deck in the transport (up & locked) position when loading or 
unloading.  Never attempt to turn the mower around on the ramp.  Avoid sudden acceleration when driving 
up a ramp and sudden deceleration when backing down a ramp. 
 

6.14 Transporting 

Use a heavy duty trailer or truck to transport the Stander ZK.  Lock brake and block wheels.  Securely 
fasten the unit to the trailer or truck with straps, chains, cable or ropes. 
 
 
 
 
 
 
 
 
 
 
 

Tightening will 

separate the hub 

from the pulley 

Threaded 

Removal 

holes 

Assembly 

hole 

Assembly 

hole 

Rear Tie Down Locations 

Front Tie Down Locations 

Summary of Contents for Stander ZK Series













































Reviews:

No comments