manualshive.com logo in svg

Wright Manufacturing Stander ZK Series, Instruction Manual, Page: 14 / 44

Share
Download
Wright Manufacturing Stander ZK Series Instruction Manual Download Page 14

14 

 

76490013 DECAL, MAIN INST PANEL 

 

76490031 DECAL, THROTTLE INSTRUCTIONS 

 

76460001 

DECAL, DANGER BLADE 

HAZARD 

 

76490001 

DECAL, SHIELD MISSING

 

 

76490050 

 DECAL, FIRE HAZARD 

WARNING

 

 

76490053 DECAL, PARKING 

BRAKE 

 

76490082 DECAL, 2" 

TRIANGLE WARNING, 

ROTATING BLADES 

 

Steering controls

 

 

Throttle, Fast/Full

 

 

Throttle, Slow/Idle

 

 

2 Warning, Safety and Instructional Decals

 

 Specific safety warning decals are located on the equipment near immediate areas of potential hazards. 

 Keep all safety signs legible.  Remove all grease, dirt and debris from safety signs and instructional 

decals. 

 Replace worn, damaged or missing safety decals. 

 If an attachment or accessory has been installed, make sure current safety decals are visible. 

1. Blade engage/disengage switch 

 

 

2. Ignition switch, Off 

3. Ignition switch, Run 

 

 

 

 

4. Ignition switch, Start 

5. Apply parking brake to start 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

1 

5 

4 

3 

2 

Summary of Contents for Stander ZK Series













































Reviews:

No comments