Air Brush Kit
AFTER SALES SUPPORT
e-mail: [email protected]
1800 909 909
MODEL: №.
TG212 • 07/2016 • 53633
(toll free)
AFTER SALES SUPPORT
(toll free)
Air Brush Kit
e-mail: [email protected]
1800 909 909
MODEL: №.
TG212 • 07/2016 • 53633
27
Problem
Possible Cause
Solution
Insufficient
pressure.
Damaged braided air hose (10).
Loose air connections.
Loose cylinder body (27) cover
screws.
Replace the braided air hose (10).
Check and tighten loose
air connections.
Tighten cylinder body (27) cover screws.
Knocks while
compressor is
loading.
Defective connection rod
bearings.
Defective wrist pins and
wrist pin bearing.
Take the compressor to one of our
qualified Service Agents for review / repair.
Take the compressor to one of our
qualified Service Agents for review / repair.
Motor does
not work
Damaged power cord.
Defective electrical wiring.
No electrical power.
Power switch is defective.
Motor is too hot.
Check the regulator has not
been adjusted too low.
Pressure is at the shut off
pressure.
Take the compressor to one of our
qualified Service Agents or a qualified
technician for review / repair.
Take the compressor to one of our
qualified Service Agents for review / repair.
Plug the power cord (2) into a working
220 volt mains power socket.
Take the compressor to one of our qualified
Service Agents for review / repair.
Turn Off the compressor at the mains
switch, remove the plug and Allow the
motor to cool for 15 minutes.
Adjust the regulator 3 turns in a clockwise
direction to increase pressure and depress
the air brush trigger.
Release air pressure by operating the
air brush.
Motor makes
strange noises
Loose or damaged bearings.
Loose connection rod screws.
Take the compressor to one of our qualified
Service Agents for review / repair.
Motor running but
no air pressure
Check the air intake filter (9).
If motor is operating continually
with no pressure and air intake
is clear.
Ensure the filter is not blocked or the holes
in the air filter cover are not blocked.
Take compressor to service agent
for review.
Spray pattern poor
Airbrush paint outlet nozzle is
dirty or blocked.
Loose air connections.
Paint is too thick.
Replace or clean the paint outlet nozzle.
Check and tighten any loose air
connections.
Mix appropriate thinner into the paint.
Suddenly stops
working
Bad valve.
Loose or damaged bearings.
Take the compressor to one of our qualified
Service Agents for review / repair.
Plug compressor into alternate electical
power source.
For all other issues, please contact Customer Service on 1800 909 909
or email [email protected]
Specifications
Compressor:
Voltage:
220-240V ~ 50Hz
Compressor Type:
Single Cylinder Piston compressor
Power:
150W S3 20%
Speed:
1450 min-
1
Air output per min/litres:
23 l/min.
Max Allowable Working
Pressure.:
4 Bar
Power Cord length:
1.5m + - 100mm
Weight:
3.5kg
Product Dimensions:
255mm (L) x 135mm (W) x 205mm (H)
Braided Air Hose
Connections:
1/8’’BSP female
Length:
1.8m
Diameter:
7 x 4mm
Air Brush Gun
Feed Type:
Siphon
Nozzle Diameter:
0.35mm
Working Pressure:
15-50 PSI
Control:
Double action
This product complies with:
EMC:
EN 55014-1: 2006 + A1:2009+A2:2011
EN 55014-2 :1997/A1:2001/A2:2008
EN 61000-3-2: 2014
EN 61000-3-3 :2013
Safety:
EN 1012-1:2010;
IEC 60335-1:2010/A1:2013
AS/NZS 60335.1:2011
