Workhorse ODYSSEY O4400F Owner'S Manual Download Page 19

 

Limited Warranty 

3730 E. Southern Avenue, Phoenix, AZ 85040 USA                       

800-778-8779 

Workhorseproducts.com 

19 

Although every effort has been made to provide accurate specifications, Workhorse Products does not assume any liability 
for damages, whether consequential or incidental, that may result from the use or misuse of the indicated specifications. 
Workhorse Products  requires the use of a licensed industrial electrician for the installation of electrical service to  equip-
ment requiring  electrical power. 

Workhorse Products reserves the right to alter specifications in the manufacture of its products. It is understood and agreed 
that Seller’s liability for any equipment whether liability in contract, in tort, under any warranty, in negligence, in strict liability 
or otherwise shall not exceed the return of the amount of the purchase price paid by Buyer. Not withstanding the foregoing 
provision, under no circumstances shall Seller be liable for special, indirect or consequential damages. The price stated for the 
equipment is a consideration in limiting Seller’s liability. No action regardless of form, arising out of the transactions under 
this Agreement may be brought by Buyer more than one (1) year after the cause of action has occurred. Our warranty is spec-
ified is exclusive and no other warranty, whether written or oral, is expressed or implied. Workhorse Products specifically 
disclaims the implied warranties of merchantability and fitness for a particular purpose. Equipment manufactured or sold by 
Workhorse Products is warranted against defects in workmanship and materials for a period of one year from receipt by cus-
tomer. All warranties initiate from date of shipment to original customer. Replacement parts are covered for the term of the 
equipment  warranty period. Parts not under  warranty are covered for thirty (30) days from receipt by customer. Any part 
found by Workhorse Products to be defective in material or workmanship within the stated warranty period will be replaced 
or repaired at Workhorse’s option without charge.  

AFTER OBTAINING AN RMA# SEND RETURNED FREIGHT PREPAID TO 3730 E. Southern Avenue, PHOENIX, AZ 85040 USA.   

Written authorization must be obtained from Workhorse before any part will be accepted. Replacement parts are sent out 
freight collect.  

Parts sent out prior to receiving defective require a credit card hold for cost plus freight. Upon return of defective part, if it 
is deemed that the part was not damaged by customer but failed, the cost of the replacement part will be refunded. 

This warranty does not extend to expendable parts such as filters, fuses, elements and brushes. Workhorse does not war-
rant failure of parts or components resulting from misuse or lack of proper maintenance. Installation, inspection, and 
maintenance costs are the sole responsibility of the purchaser.

 

Summary of Contents for ODYSSEY O4400F




















Reviews: