Woodhead SST-PFB3-ISA Hardware Reference Manual Download Page 22 | Manualshive

Page: 22 / 63

background image

Hardware Reference Guide

SST-PFB3-ISA

22 Installation

©2004 Woodhead Software & Electronics, Division of Woodhead Canada Limited

Document Edition: 1.0, Document #: 715-0078, Template Edition: 1.1, Template #: QMS-06-045

Use, duplication or disclosure of this document or any of the information contained herein is subject to the restrictions on page ii of this document.

2.4 Downloading a Firmware Module

For instructions on downloading a firmware module to the card, refer to Section C.1,

Loading a Firmware Module

.

2.5 Connecting to a Profibus Network

This section provides connection, termination, power and grounding details.

2.5.1 Connecting the DB9

The following table describes how to connect the Profibus DB9.

Table 6: DB9 Instructions

DB9 Pin Description

DB9 Pin #

DB9 Termination with Card

Chassis ground

1

Reserved 2

Data +

3

Connect this pin to Pin 8 (data -)
with 220 ohm resistor

Tx enable

4

Isolated ground

5

Connect this pin to Pin 8 (data -)
with 390 ohm resistor

Voltage plus

6

Connect this pin to Pin 3 (data +)
with 390 ohm resistor

Reserved 7

Data -

8

Reserved 9

«
...
20
21
22
23
24
...
»

Summary of Contents for SST-PFB3-ISA
































































Reviews:

No comments

Related manuals for SST-PFB3-ISA

Brand: Taylor Made Pages: 2

Brand: York Fitness Pages: 18

Brand: Safco Pages: 2

Brand: Omni Pages: 193

Brand: IDEAL Networks Pages: 10

Brand: Qlight Pages: 4

Brand: Saadat Pages: 61

Brand: Saadat Pages: 22

Brand: ubicquia Pages: 4

Brand: Woodward Pages: 62

Brand: Woods Pages: 54

Brand: Neilsen Pages: 8

Brand: ZOE Pages: 40

INOblender 10026

Brand: Mallinckrodt Pages: 38

Brand: Emos Pages: 5

OMNISTIM FX2 CYCLE/WALK

Brand: Accelerated Care Plus Pages: 30

Brand: g-lites Pages: 24

Orux 480 Z Profile

Brand: Gamma Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands