manualshive.com logo in svg

WoodFast DP300A, Instruction Manual

Share
Download
WoodFast DP300A Instruction Manual Download Page 13

-13-

6.8     TO REPLACE THE BELT 

Disconnect the bench drill press from the power source 

before replacing the belt. 

FIG.6.8

CAUTION

CAUTION

Belt tension and bench drill press speed is controlled by 

automatic adjustments made to the diameter of the front 

spindle when the drive handle is moved.

 

- Remove the screw that secures the housing cover (1). 

Open the housing cover.FIG.6.8

- Remove the belt (2) from the housing cover if it is 

broken. If it is not broken, but is too stretched to operate 

correctly, work the belt off the drive (motor) spindle (3). 

Then remove the belt from the front spindle (4).FIG.6.8

- Replace the belt by putting a new belt over the front 

spindle (4) and carefully sliding the belt over the drive 

(motor) spindle (3).FIG.6.8

See page 17 for information on the variable speed function of this bench drill press.

Do not change the drive speed when the bench drill press is turned off. 

 7.1    BENCH DRILL PRESS ON/OFF SWITCH 

- To turn the drill press ON for starting.
- To turn the drill press OFF for stopping.

 7.2    

TO DRILL A HOLE

- Mark where you want to drill in workpiece by using a center punch or a sharp nail or turn ON Laser Line to mark 

drilling point.

- Before tuming ON the bench drill press, turn the feed handles to bring the drill bit down. Line the drill bit tip up with the 

mark. Clamp the workpiece in place.

- Tum ON the bench drill press and pull down on the feel handles with appropriate force needed to allow the drill bit to 

drill material.

7   OPERATION

8   GENERAL DRILLING GUIDELINES

To prevent the workpiece and the backup material from slipping from your hand while drilling, position workpiece and 

backup material to the left side of the column. If the workpiece and the backup material are not long enough to reach the 

column, clamp workpiece and backup material to the table. Failure to do this could result in personal injury. 

To drill a hole: 

- Mark where you want to drill in workpiece by using a centre punch or a sharp nail or turn ON Laser Line to mark drilling 

point.

- Before turning ON the bench drill press, turn the feed handles to bring the drill bit down. Line the drill bit tip up with the 

mark. Clamp the workpiece in place.

- Turn ON the bench drill press and pull down on the feed handles with appropriate force needed to allow the drill bit to 

drill material.

Summary of Contents for DP300A


















Reviews:

No comments

Brands by name

Popular brands

Load more brands