background image

03

echnical Specification

T

600 ml

Container capacity

100 0W

250W

50W

Rating power

Main Unit

Rating pressure

Water pressure 

range

Electrical wire

length is about 1.8m

Minimum water pressure 0.07MPa (20L/min. flowing pressure). 
Maximum water pressure 0.8MPa (Hydrostatic pressure)

1050-1250W

AC 110-120V,50/60Hz

Heating power

Water 

temperature

W

ater volume

Cleansing mode
Spray cleansing
location

Water pressure

protector

Cleaning
device

Anti-fouling device

Safety device

6 different level adjustment

5 different level adjustment

5 different level adjustment

Rear cleaning/Rear massage,Front cleaning for ladies

Pressure stabilize ,Automatic pressure discharging

Speedy water discharge device,  Automatic nozzle cleaning,

Anti-syphon device, Anti-backflow device, Filter  device

Warm wind speed

Warm wind 

temperature

Heating power

Safety device

Drying
device

6 different level adjustment

6 different level adjustment

Over 4 M/S

Temperature sensor, Temperature controller, Thermal fuse

Temperature controller, Thermal fuse, Ground protection, 
Leakage protection device, Air burning preventer

Heated seat

Surface

temperature

Heating power

Open and close

device

Heated burning

protection

Safety device

Quiet soft-closing device

The seat temperature will automatically lower to level

1 in 10 minutes after using

Seat sensor, emperature sensor, Temperature controller, 

T

Thermal fuse

Intelligent

 

Night light

assembly

Mute setting

Intellignt,often in the off state

Buzzeroff during night

User ID setting To avoid disturbance from remote controls by multi-user

Summary of Contents for B0940S
















Reviews: