Wood master Flex Fuel Owner'S Manual Download Page 25

Page: 25 / 76

March 2011

Flex Fuel Owner’s Manual

8: Display

8.1 The Starting Screen

The displayed values are current actual values. The boiler temperature,

the flue gas temperature and the air factor are displayed.

The lowest line(s) of the starting screen is/are the status line(s). The status line shows the operating

status of the furnace.

Note: This furnace runs on DD/MM/YY date format and on military time format.

The currently selected furnace operating mode is displayed. Depending on the furnace model, the

following furnace operating modes are available:

• Bulk materials

• Bulk materials auto control

• Pellets auto control

Read further in this section to gain a better understanding of menu navigation, otherwise proceed to

the next section.

FLEX FUEL

V 10.060 Tu, 12.09.10

Bulk materials
Boiler temperature:

Flue gas temperature:

Air factor:

Boiler is switched off!

81ºF

13:44

117ºF

7.40

Software Version

Date & Clock

Current

Actual Values

Selected

Furnace Mode

Status Line(s)

Summary of Contents for Flex Fuel













































































Search results

Summary of Contents for Flex Fuel

Reviews:

Related manuals for Flex Fuel

Brands by name

Popular brands

Wood master Flex Fuel, Owner'S Manual

Search results

Summary of Contents for Flex Fuel

Reviews:

Related manuals for Flex Fuel

Brands by name

Popular brands