Wood master Flex Fuel Owner'S Manual Download Page 27

Page: 27 / 76

March 2011

Flex Fuel Owner’s Manual

Changing/Viewing Individual Settings

By turning the control knob, you can:

• Navigate between various main menu levels,

• Navigate within a menu,

• View or change individual settings.

A symbol appears in the upper right hand corner of the screen, which will show you at which level you

currently are.

Note: By pressing the ESC key, you will always move back one level, no matter where you are.

You will always return to the starting screen. Data WILL NOT be changed by using the ESC key.

8: Display

UP/DOWN SYMBOL

If this symbol appears, navigate within the just displayed

menu by turning the control knob.

RIGHT/LEFT SYMBOL

If this symbol appears, scroll between various main

menus by turning the control knob.

CHANGE SYMBOL

If this symbol appears on the screen, you will change

a single setting by turning the control knob. If you turn

the knob clockwise, the value increases; if you turn it to

the counterclockwise, the value is reduced.

BOILER OPERATING MODE

Bulk materials

Bulk materials auto control

Pellets auto control

Selected boiler mode:

Pellets auto control

Symbol example

Summary of Contents for Flex Fuel













































































Search results

Summary of Contents for Flex Fuel

Reviews:

Related manuals for Flex Fuel

Brands by name

Popular brands

Wood master Flex Fuel, Owner'S Manual

Search results

Summary of Contents for Flex Fuel

Reviews:

Related manuals for Flex Fuel

Brands by name

Popular brands