Wood master Flex Fuel Owner'S Manual Download Page 31

Page: 31 / 76

March 2011

Flex Fuel Owner’s Manual

Move the curser by turning the control knob to the output test – boiler line and press the control knob.

The menu “OUTPUTS 1” appears on the screen.

You can now press the control knob to scroll through the items to select one to change. If the control

knob is turned to the right while the cursor is in the heading, then the menu “OUTPUTS 2” appears for

more options. You may turn the control knob again to bring up the “OUTPUTS 3” menu.

Switching on the Outputs

In order to test an output, press the control knob in the header. The cursor moves back to the first menu

item. By turning the control knob, select the system components that you would like to test and press

the control knob again. The cursor now moves to the respective setting parameter, which you can

change by turning the control knob. Confirm your entry with the control knob and verify that the

respective system component is really activated.

Press the ESC key to exit this menu. The cursor now moves to the header and you will exit this menu by

pressing the ESC key. All activated components are automatically switched off.

9.10 Language Selection/Temperature Scale Selection

In this menu you can select your desired language and temperature scale.

9: Basic Furnace Settings

OUTPUTS 1

Primary magnet(5):

Ignition(1):

Burnback Prot.(3):

Heat exchanger(17):

RIB pump(4):

Ash extraction(16):

sec. air flap(6):

sec. servo motor(6):

Lamb. sensor(10):

Ind. draft fan(7):

Off

Off Close

Off

Close

Off

02: 21.0%

Man 0

LANGUAGE SELECTION

German

Italian

French

English

Spanish

Please select your

language!

Temperature unit: °F -> °C

Summary of Contents for Flex Fuel













































































Search results

Summary of Contents for Flex Fuel

Reviews:

Related manuals for Flex Fuel

Brands by name

Popular brands

Wood master Flex Fuel, Owner'S Manual

Search results

Summary of Contents for Flex Fuel

Reviews:

Related manuals for Flex Fuel

Brands by name

Popular brands