manualshive.com logo in svg

Wolf R1, Installation And Operating Instructions Manual, Page: 7 / 36

Share
Download
Wolf R1 Installation And Operating Instructions Manual Download Page 7

7

3061809_1210

Commissioning

Switch ON the system ON / OFF switch at the control unit.

ON / OFF switch

The heating system starts to operate with the factory settings as 

soon as the ON / OFF switch at the control unit is switched ON.

Note:

The factory settings of the control unit represent empirical values. 

Subject to system or equipment level, control parameters other 

than those chosen at the factory can be selected. Make changes 

via the Wolf control accessories or via a PC / laptop with Wolf 

control software. All factory settings are stored in a non-volatile 

memory.

During commissioning, the control unit automatically recognises 

any connected cylinder and / or outside temperature sensor.

The outside temperature sensor is logged off by disconnection and 

by switching the supply voltage OFF and ON again.

The  system  will  not  be  protected  against  frost  if  no  outside 

temperature  sensor  is  connected;  only  the  boiler  is  frost 

protected.

You  can  log  off  the  cylinder  sensor  by  disconnecting  and 

resetting.

The boiler sensor cannot be logged off.

NB

Summary of Contents for R1





































Reviews:

No comments