manualshive.com logo in svg

Wolf R1, Installation And Operating Instructions Manual, Page: 6 / 36

Share
Download
Wolf R1 Installation And Operating Instructions Manual Download Page 6

3061809_1210

6

Pump connection

Wolf boiler circuit and DHW cylinder primary pumps are factory-

fitted with plugs. Route the cable through the boiler back cutout. 

Insert the plug into the marked-up locations in the plug-in connector 

strip, and secure the cables with their strain relief. 

Installation / Electrical work

Outside temperature 

sensor

(accessory)

Join the on-site lead of the outside temperature sensor with the 

plug supplied. Insert the plug into the marked-up location in the 

plug-in connector strip, and secure the lead with its strain relief. 

Route  the  lead  through  the  boiler  back  cutout.  Fit  the  outside 

temperature  sensor  to  the  north  or  northeast  wall,  2  to  2.5m 

above ground level. 

DHW sensor

(accessory)

Push the DHW cylinder sensor (accessory) into the cylinder sensor 

well. Route the lead through the boiler back cutout. Insert the plug 

into  the  marked-up  location  in  the  plug-in  connector  strip,  and 

secure the lead with its strain relief.

E1

programmable input

Join the cable of input E1 with the plug supplied. Insert the plug 

into  the  marked-up  location  in  the  plug-in  connector  strip,  and 

secure the cable with its strain relief. Route the cable through the 

boiler back cutout.

eBUS accessories

Remote control, radio clock module, radio clock module with outside 

temperature  sensor,  receiver  for  wireless  outside  temperature 

sensor and wireless analog remote control.

Join  the  on-site  accessory  cable  with  the  green  plug  supplied 

(designated eBUS). Insert the plug into the marked-up location 

in the plug-in connector strip, and secure the cable with its strain 

relief. Route the cable through the boiler back cutout.

Note:

If several eBUS accessories are to be connected simultaneously, 

connect these in parallel at the eBUS terminal.

A1

programmable output

Join the cable of output A1 to the plug supplied. Insert the plug 

into  the  marked-up  location  in  the  plug-in  connector  strip,  and 

secure the cable with its strain relief. Route the cable through the 

boiler back cutout.

Summary of Contents for R1





































Reviews:

No comments