manualshive.com logo in svg

Wolf R1, Installation And Operating Instructions Manual, Page: 35 / 36

Share
Download
Wolf R1 Installation And Operating Instructions Manual Download Page 35

35

3061809_1210

Fault messages

If a fault is indicated by the signal ring of the control unit fl ashing red, a fault code is displayed 

via the Wolf control accessory with eBUS capability that allows cause and effect to be allocated 

using the following table.

This list of fault messages is designed to allow your heating contractor to trace the fault more 

easily.

No. Fault

Cause

Effect / Remedy

1

TB excess temperature

The external temperatu-

re limiter has shut down 

the system

Burner OFF, pump ON

Request a service

4

Burner fault

During the burner start 

no fl ame was esta-

blished

Burner OFF, pump ON

Press the reset button at the com-

bustion controller or the control unit.

If the fault cannot be removed by 

pressing the reset button several 

times, request a service.

6

TW excess temperature The boiler water tem-

perature has exceeded 

the limit for TW (e.g. 

95 °C)

Burner OFF, pump ON

Request a service

8

Flue gas/ventilation air 

damper does not move

Flue gas damper / ven-

tilation air damper or its 

feedback faulty

Burner OFF, pump ON

12

Boiler sensor faulty

Boiler temperature 

sensor or lead faulty

Burner OFF, pump ON

Request a service

14

Cylinder sensor faulty

Sensor for the DHW 

temperature or for the 

lead faulty

For heating mode:

No effect

Cylinder primary pump and heating 

circuit pump cycle 

alternately

1 h ON,

1 h OFF

Request a service

40

Fault maximum thermo-

stat, system pressure 

limiter

The system pressure 

switch or the maxi-

mum thermostat has 

responded

Burner OFF, pump OFF

52

Max. cylinder heating 

time exceeded

Cylinder heating takes 

longer than permitted

Alternating cylinder heating and 

central heating mode

15

Outside temperature 

sensor faulty

Sensor for the outside 

temperature faulty

(short circuit or break)

Effect as per outside temperature 

below frost protection limit

Request a service

79

Fault multi-function sen-

sor (central sensor)

Central sensor faulty 

(short circuit or break)

Control unit at set boiler water temp. 

No effect on the boiler operation

Request a service

79

Fault multi-function sen-

sor (return sensor)

Sensor for the return 

sensor faulty (short 

circuit or break)

No effect on the boiler operation 

bypass pump continues to run

Request a service

81

Fault EEPROM

Internal equipment fault Request a service

91

Fault eBUS parameter

One BUS address was 

allocated more than 

once

Request a service

Summary of Contents for R1





































Reviews:

No comments