Wolf L282212I Installation Instructions Manual Download Page 4

I N S T A L L A T I O N
C O N S I D E R A T I O N S

1)

A straight, short duct run will

allow the hood liner to perform more
efficiently. Try to limit the number of
elbows and transitions to as few as
possible. Long duct runs, elbows and
transitions will reduce the perform-
ance of the hood liner.

IMPORTANT NOTE:

All hoods must

exhaust to the outdoors.

IMPORTANT NOTE:

There is a possi-

bility of noise issues, if there is a short
duct run coupled with a remote
blower.

2)

Always use metal ducting. Do not

use flex ducting.

3)

Wolf recommends installing a

back-draft damper in all installations
(included with hood liner). In cold
weather installations a back-draft
damper is necessary to minimize the
backflow of cold air into the room.

4)

Wolf recommends the hood liner

be installed 30" to 36" above the
cooking surface.

5)

Local building codes may require

the use of make-up air. Consult your
local HVAC professional for specific
requirements in your area.

4

Liner Installation Dimensions

30" 

TO

 36"

(762 mm - 914 mm)

COOKING SURFACE

TO BOTTOM OF

HOOD LINER

12" 

(305 mm)

HEIGHT OF LINER

HOOD LINER

DUCTWORK INSTALLATION

THROUGH ROOF

 37" 

(940 mm)

TO COOKING

SURFACE

ROOF CAP

10" ROUND DUCT

SOFIT OR CABINET

OR DUCT COVER  

*TOP DISCHARGE ONLY FOR VENTILATION HOOD LINERS

TOP DISCHARGE*

TRANSITION

22

1

/

2

"

(572 mm)

DEPTH OF LINER

DECORATIVE HOOD

WARNING

To reduce the risk of fire and
electric shock, install this
hood liner only with the
blowers manufactured by
Wolf Appliance Co., Model
numbers 805087, 805347,
801640, 801641, 801642 and
804701.

P

R O

S

E R I E S

V

E N T I L A T I O N

H

O O D

L

I N E R S

Summary of Contents for L282212I

















Reviews: