Wohler iAM2-8 User Manual Download Page 77 | Manualshive

Page: 77 / 116

background image

Page 77

5.

The new software version that is in the flash drive will be shown in the

Software Version

screen. To cancel the upgrade at this point for any

reason, touch

Back

. To proceed, touch the software version entry in the

Software Version

screen. A screen will appear, as shown in Figure A-3.

Figure A-3 - Upgrade Verify

Software Upgrade

Back

Software Version

3.4-39

Wohler iAM-AUDIO

3.4-56

?

Are you sure?

Do you want to Update your System to
1.1.3?

Yes

No

6.

To proceed, touch

Yes

. To back out, touch

No

. After you touch

Yes

, the

screens will change, as shown in Figure A-4. The message on this screen will
change as the upgrade progresses. The left screen will display, "Software
Upgrade in Progress" until the upgrade is complete.

Figure A-4 - Upgrading System

System Update

Software Version

1.1.3

Back

Upgrading System.

Refresh

Installing Package

7.

After the software update starts, the text on the left screen will change
periodically to indicate the progression of the upgrade. The upgrade will take
5 minutes or more, after which the iAM2-8 will restart. After the system has
completed its restart cycle and is once again operational, you may then
remove the flash drive.

«
...
75
76
77
78
79
...
»

Summary of Contents for iAM2-8





















































































































Reviews:

No comments

Related manuals for iAM2-8

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 34

Brand: Panasonic Pages: 8

ACUSTICA H series

Brand: RCF Pages: 10

Welder / Generator GW4500

Brand: Campbell Hausfeld Pages: 20

Brand: Abbyson Pages: 7

Grand Touring GTO428

Brand: JBL Pages: 2

Intellex DV16000

Brand: American Dynamics Pages: 201

weldmatic 350i CP139-2

Brand: WIA Pages: 28

Brand: Laney Pages: 12

Area Line Pressure Alarm

Brand: BeaconMedaes Pages: 10

Brand: Watts Pages: 73

Brand: Metra Electronics Pages: 12

Brand: TCL Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands