© 2006 Wohler Technologies Inc. ALL rights reserved
19
AMP-S8
User Manual P/N
821640
Rev-
B
7g
R DOWN (
ENTER
) Button
Selection Navigation Using the UP and DOWN Buttons:
> R DOWN (or R UP) Button
The
R DOWN
or
R UP
(and
L DOWN
or
L UP
)
Buttons
are used to cycle through and select different channels or
channel combinations, depending on which
Selection Mode
is selected. See
Single Channel Selection
,
Paired Channel
Selection
, and
Downmix Selection
on page
25
for more information about using these buttons for channel selection.
Using the
ENTER
Button:
When in
Setup Mode
, The
ENTER
Button
and is pressed to accept menu selections. Also see
Enabling Setup Mode
(page
28
) and the
Setup Menu Navigation Flow Chart
(
Figure-2e
, page
31
) for more detailed information.
R UP (
ESC
) Button
Selection Navigation Using the UP and DOWN Buttons:
> R UP (or R DOWN) Button
The
R UP
or
R DOWN
(and
L UP
or
L DOWN
)
Buttons
are used to cycle through and select different channels or
channel combinations, depending on which
Selection Mode
is selected. See
Single Channel Selection
,
Paired Channel
Selection
, and
Downmix Selection
on page
25
for more information about using these buttons for channel selection.
Using the
ESC
Button:
In
Setup Mode
, the
ESC
Button
is used to exit, or back out of, any of the menus within
Setup Mode
without accepting
changes. Also see
Enabling Setup Mode
(page
28
) and the
Setup Menu Navigation Flow Chart
(
Figure-2e
, page
31
)
for more detailed information.
7f
7e
DM3 SD.SDI2 DM3
DM3 SD.SDI2 DM3
DM3 SD.SDI2 DM3
DM3 SD.SDI2 DM3
DM3 SD.SDI2 DM3
GP1 GP2
GP1 GP2
GP1 GP2
GP1 GP2
GP1 GP2
1 3 5 7
1 3 5 7
1 3 5 7
1 3 5 7
1 3 5 7
2 4 6 8
2 4 6 8
2 4 6 8
2 4 6 8
2 4 6 8
Source Status
(
SD-SDI Input 2
)
SDI Group
(
Group #2
)
Input Lock Status
(
Channels 1, 2, 3, 4,
5, 6, 7, 8 Locked
)
Mix Status
(
Downmix
DM3
)
SDI Group
(
Group #1
)
Mix Status
(
Downmix
DM3
)
LCD Display
In
Normal Operational Mode
the high-contrast
LCD Display
is used to report the currently selected
channels
for
reproduction along with selected
source type
,
mix type
, and any
SD/HD-SDI
audio
group
information (for products with
the
SDI
inputs). In other modes the display will indicate
phase correlation
and
mute status
. In
Setup Mode
, the display is
used to navigate
menus
, select
parameters
, and recall and name
presets
.
In normal operation (
not
muted), the
Input Lock Status
indicator (center of second line in display) is used to show the lock
status of selected
digital
inputs (including
SDI
sources). If all four input channel pairs are not locked (or connected), then
four short dashes are displayed in the center of the second line of the display. Each dash (-) indicates a position for
displaying the channel pairs available for monitoring. The display appearance and order (from left to right) is:
1/2
,
3/4
,
5/6
and
7/8
. The input status is updated whenever a change in status is detected. The
Input Lock Status
is active only if one
of the
digital
sources is selected via the
INPUT Button
(
Item 7i
), and applies only to the
digital
source that is selected.
Status Display Examples - Input Sources:
User Interface Features
Section 2:
Operation
MIX HD.SDI1 MIX
MIX HD.SDI1 MIX
MIX HD.SDI1 MIX
MIX HD.SDI1 MIX
MIX HD.SDI1 MIX
GP3 -- GP4
GP3 -- GP4
GP3 -- GP4
GP3 -- GP4
GP3 -- GP4
5 7
5 7
5 7
5 7
5 7
6 8
6 8
6 8
6 8
6 8
Source Status
(
HD-SDI Input 1
)
SDI Group
(
Group #4
)
Input Lock Status
(
Channels 1, 2, 3, 4 Not
Locked; Channels 5, 6, 7, 8
Locked
)
Mix Status
(
Custom
)
SDI Group
(
Group #3
)
Mix Status
(
Custom
)
