Wohler A 550 Operation Manual Download Page 58

Page: 58 / 79

Fig. 56: Probe grip with Peltier Cooler

and USB power bank

•

Connect the Peltier Cooler and ist portable

USB power bank as described in the Manual

USB Peltier cooler.

•

NOTE!

Take care that the Peltier Cooler has enough

power during the long time measurement. For

measurements that take more than 5 hours we

recommend to connect the USB power bank.

Before starting

Before starting a long term logger measurement:

•

Configure the logger measurement.

•

Ensure sufficient battery power is available or

connect the analyzer to main power.

•

Press Start button to activate the logger

measurement

•

The ON/OFF button will flash during intervals

> 8 min

•

When the logger measurement is finished

connect the analyzer to a computer to down-

load the data (please refer to Wöhler A 550

Data Management PC Software manual).

Summary of Contents for A 550
















































































Search results

Summary of Contents for A 550

Reviews:

Related manuals for A 550

Brands by name

Popular brands

Wohler A 550, Operation Manual

Search results

Summary of Contents for A 550

Reviews:

Related manuals for A 550

Brands by name

Popular brands