WITTUR sematic SRS DC-PWM, Instruction Manual

Page: 24 / 28

24
www
.wittur
.com
Changes can be made without notice
PM.2.004922.EN - 810-000-000 SRS DC-PWM
©
· Edition 22 July 2020
"Menu": pushing key F2 go back to "Main Menu"
8.5.7 LA THRESOLD
For the meaning of this parameter see point “6.8 LA Thresold (Instruction with handset)” a pag. 16
• Using keys
ã
and
ä
run through menu GENERAL OPTION selecting LA THRESOLD
• Press Ok to confirm the chioce
• On the display will be showed the parameter "LA THRESOLD"
• Using keys
ã
and
ä
for increase and decrease the value
• Press OK to store the setting data
• After that on the display will be showed the parameter "FIANL LOW SPEED OP ".
• Using keys
ã
and
ä
for increase and decrease the value
• Press OK to store the setting data
• The controller will store the setting come back to the menu "General Option"
Following options are available
• "Back": pushing key F1 go back to "Main Menu"
• "Menu": pushing key F2 go back to "Main Menu"
8.6 MAINTENANCE MENU - DIAGNOSTICS AND ALARM MANAGEMENT
8.6.1 Consulting the Maintenance Menu with the Handset
• Connect the handset to the RJ45 connector
• Using keys
ã
and
ä
to choose the required language and confirm with the “OK”
• Using keys
ã
and
ä
to run through the “MAIN MENU“and choose “MAINTENANCE”
• Press “OK” to confirm the choice
• The following options are viewed on the display:
− STATISTICS
− LAST ALARMS
− LOOP
− DISPLAY CONTRAST
− MLC MONITOR (MAIN LIFT CONTROLLER MONITOR)
− WARRANTY DATA
− SET FACTORY DEFAULT
− MANUFACTURER MENU
• The following options are available
− “BACK”: Press key F1 to restore the MENU MAINTENANCE
− “MENU”: Press key F3 to restore the MAIN MENU
• Using keys
ã
and
ä
, run through the MAINTENACE menu and choose the required option
• Press “OK” to confirm the choice
If the option STATISTICS is chosen, the display shows the door total working time expressed in days:hours:minutes, the cycle total
number which have been performed in this working time and the manufacture date. The following options are available:
• "BACK": Press key F1 to restore the menu Maintenance
• "MENU": Press key F3 to restore the Main Menu
If the option LAST ALARMS is chosen the display shows the last occurred alarms showing their code, the relevant description and time
of occurrence (day :hour :minute from the door controller start-up). Using keys
ã
and
ä
, run through the stored alarm list. The following
options are available:
• “BACK”: Press key F1 to restore the menu MAINTENANCE
• “CANC”: Press key F2 to cancel all stored alarms
• “MENU”: Press key F3 to restore the MAIN MENU
The showed alarms are those as in table in “6.10 Alarms” a pag. 16
If the option LOOP is chosen is possible to make some door trial opening and closing cycle.
The following options are available
• "Loop": Pressing key F1 the door performs a number of consequent opening and closing cycles until key F1 is pressed again
• "<>" or " >< ": Press key F2 to let the doors respectively open or close
• "MENU": Press key F3 to restore the Main Menu
If the option DISPLAY CONTRAST is chosen, the display shows a dark square and allows the setting of the LCD contrast, by means of the
á
and
â
keys; adjust to best view and confirm with "OK" key.
The following options are available:
• "BACK": Press key F1 to restore the menu MAINTENANCE
• "MENU": Press key F3 to restore the MAIN MENU
If the option MAIN LIFT CONTROLLER MONITOR is chosen, the system accepts the Main Lift Controller signals; the display shows a
complete list of the input/output signals with their value.
When the input or output signal is activated the character on the display will change their graphic in white with dark background.
The following options are available:
• “BACK”: Press key F1 to restore the menu MAINTENANCE
• “MENU”: Press key F3 to restore the MAIN MENU
If the option WARRANTY DATA is chosen, the display shows:
• warranty expiration date
• the activity hours left before warranty expiration
• the software version in use