Wisenet TNM-3620TDY User Manual Download Page 9

Page: 9 / 22

English _

INST

ALLA

TION & CONNECTION

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Connect to WiFi dongle

Camera Setup
1.

Connect OTG adapter (5-pin) and WiFi dongle to the micro USB port.

Smartphone Setup
1.

Install the Wisenet Installation application.

Select the camera SSID after turning on the WiFi.

Run the Wisenet Installation application.

When you log in to the camera, the video will be connected.

The video will be played without being logged in during the initial connection.

You can adjust angle of view while watching the video through smartphone.

Recommended dongle manufacturer

Manufacturer

Model

NETIS

WF2123 n300

EDIMAX

EW-7811Un

IP Time

N100mini

TP-LINK

TL-WN823N V1

ASUS

USB-N13

ASUS

USB-N10 NANO

NETGEAR

WNA3100M

IODATA

WN-G150UMW

CONNECTING WITH OTHER DEVICE

Grounding cable

Wi-Fi dongle

Monitor for installation

Power

PoE+ Router

The Test Monitor Out port of the product is provided for easier installation, and is not recommended for monitoring purposes.

The Micro USB out terminal of the product is provided for easier installation, and is not recommended for monitoring
purposes.

Wi-Fi dongle for product installation displays only <

CH1 : Visible

> video.

If the screen freezes for about 1-2 seconds at a certain time interval or when there is a change in the temperature of the
surrounding area, this is normal; the screen is simply undergoing a calibration process.

Summary of Contents for TNM-3620TDY























Search results

Summary of Contents for TNM-3620TDY

Reviews:

Related manuals for TNM-3620TDY

Brands by name

Popular brands

Wisenet TNM-3620TDY, User Manual

Search results

Summary of Contents for TNM-3620TDY

Reviews:

Related manuals for TNM-3620TDY

Brands by name

Popular brands