Wisenet TNM-3620TDY User Manual Download Page 12

Page: 12 / 22

installation & connection

12_

installation & connection

Connecting to the I/O port box

Connect the Alarm I/O cable to the corresponding port of the port box.

Sensor

Alarm

(Warning lamp)

ALARM-IN : Used to connect the alarm input sensor or external day/night sensor.

ALARM-OUT : Used to connect the alarm output signal.

GND : Common ground port for alarm in/output signal.

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open
collector method, it may cause malfunction.
Refer to the “

Alarm Out Wiring Diagram

” when connecting devices such as a warning lamp or a siren.

To connect the external sensor

Connect one signal line of a 2-wire sensor to the [

ALARM IN

] port and connect the other wire to the [

GND

]

port.

Alarm In Wiring Diagram

Alarm Out Wiring Diagram

Sensor

GND

RESISTOR

ALARM IN (5mA SINK)

RESISTOR

VCC_3.3V

DIODE

GND

MLCC

TRANSISTOR

External

connection

Inside of the camera

Warning lamp /

Siren power

Warning lamp /

Siren

ALARM OUT (12VDC 20mA MAX)

RESISTOR

10K ohm

DIODE

RELAY

DC 5V or 3.3V

TRANSISTOR

GND

TRANSISTOR

External connection

Inside of the camera

GND

RESISTOR

Summary of Contents for TNM-3620TDY























Search results

Summary of Contents for TNM-3620TDY

Reviews:

Related manuals for TNM-3620TDY

Brands by name

Popular brands

Wisenet TNM-3620TDY, User Manual

Search results

Summary of Contents for TNM-3620TDY

Reviews:

Related manuals for TNM-3620TDY

Brands by name

Popular brands