DMX Interface
Transceivers on bus: 32 (max)
Data rate: 250 kbps (max)
ESD protection*: ±15 kV
AC input
90-250VAC 50/60Hz
1A at 115VAC (max)
0,5A at 230VAC (max)
DC input
12VDC 1,5A (max)
Compliance declarations
ETSI: EN300 328 & 300 826
EMC: EN301 489-17
CE: EN60950
FCC: UQT-WDXOEMPCBF
IC: 6812A-WDMXOEM
ARIB: 06215559/AA/00
RF characteristics
Output power:
20 25** dBm
100 300** mW
Frequency range:
2402 to 2479 MHz
Channel bandwidth: 1
Sensitivity at 0.1% BER:
-95dBm
* Slewrate limited for
minimum of EMI in unter-
minated networks.
** Only in FCC output
power mode.
Package Contents
In addition to this manual:
1 pc, BlackBox R-512
1 pc, Power cord
1 pc, DC connector
1 pc, Standard antenna
1 pc, Antanna adaptor
2 pc, Trussholder brackets
BlackBox
R-1
Receiver
Installation
1 Attach the antenna to the connector on the front panel. If using
the standard antenna, use also the supplied adaptor.
2 Link the DMX source to the
DMX in
socket on the rear panel.
3 Connect power to the unit either via the AC power input (90 to
250VAC), the DC power input (12VDC) or via the DMX bypass
RJ45 socket (12VDC). If using the AC input, fit an appropriate
mains plug to the supplied power cord -
this should be carried
out only by a qualified electrician
.
4 If required, attach the supplied trussholder brackets to the top
cover of the unit (see page 12).
To link with a transmitter
1 Ensure that this receiver is not linked with any other transmitter
(
LINK
indicator should be OFF).
2 On the transmitter unit, press and release the
FUNCTION
button.
The transmitter will scan for all unlinked receivers for a period of
ten seconds.
3 If successful, the receiver’s
LINK
indicator will go ON. One or
more
Level
indicators will then show the signal strength.
To unlink from a transmitter
1 On the receiver, press and hold the
FUNCTION
button until the
LINK
indicator goes OFF. The receiver is now unlinked.
AC power input
(90-250VAC)
DC power input
(12VDC)
DMX out (RJ45)
1: DMX- 5: n/c
2: DMX+ 6: n/c
3: n/c
7: Signal GND
4: n/c
8: n/c
DMX out,
(XLR female 5pin)
Reserved
DMX out, DC power in (RJ45)
1: DMX-
5: +12VDC
2: DMX+
6: n/c
3: n/c
7: Signal GND
4: +12VDC 8: DC GND
LINK
OFF: Not linked to a transmitter
ON: Linked to a transmitter
RAPID FLASH: Linking with a transmitter
W-DMX
made in sweden
Level
Radio
Batt
Wireless Solution
Sweden AB
FUNCTION
POWER
DATA
RX
TX
CTRL
LINK
R-512
RX
W-DMX
made in sweden
Level
Radio
Batt
Wireless Solution
Sweden AB
FUNCTION
POWER
DATA
RX
TX
CTRL
LINK
RADIO
Indicates that Level
display is showing
signal strength
BATT
Not used
FUNCTION
Press for 5
seconds to unlink
from transmitter
Level
Provides indication of radio
signal strength when linked to a transmitter
DATA
ON: Receiving DMX data
TX
&
CTRL
Not used
POWER
ON: Correct power
input present
