DMX Interface
Transceivers on bus: 32 (max)
Data rate: 250 kbps (max)
ESD protection*: ±15 kV
AC input
90-250VAC 50/60Hz
1A at 115VAC (max)
0,5A at 230VAC (max)
DC input
12V-24DC 1,5A (max)
Compliance declarations
ETSI: EN300 328 & 300 826
EMC: EN301 489-17
CE: EN60950
FCC: UQT-WDXOEMPCBF
IC: 6812A-WDMXOEM
ARIB: 06215559/AA/00
RF characteristics
Output power:
20 25** dBm
100 300** mW
Frequency range:
2402 to 2479 MHz
Channel bandwidth: 1
Sensitivity at 0.1% BER:
-95dBm
* Slewrate limited for
minimum of EMI in unter-
minated networks.
** Only in FCC output
power mode.
Package Contents
In addition to this manual:
1 pc, BlackBox T-1 Pro
1 pc, Power cord
1 pc, DC connector
1 pc, Standard antenna
1 pc, Antanna adaptor
2 pc, Trussholder brackets
Installation
Please see page 4 for details.
When fully charged, the internal battery can support operation for
up to 2 hours. Use the button on the rear panel to change be-
tween battery operation (green indicator) and external power (red
indicator). When no external power is supplied, this switch can be
used to cease battery operation and power down the unit.
IMPORTANT
Only one DMX universe input
may be connected at any time
AC power
input
(90-250VAC)
DC power
input
(12-24VDC)
DMX in
(see S-1 for
pin-out)
DMX out,
(XLR female
5pin)
Reserved
DMX out,
DC power in
(see S-1 for
pin-out)
DMX in,
(XLR male
5pin)
Mode button - Press to
change T1 between trans-
mitter and receiver. See
front panel TX & RX indica-
tors for current mode.
Battery button & indicators - Press
to change between battery (green
indicator) and external power input
(red indicator) operation.
W-DMX bus
port - for
connection to
another T-1
unit or to a PC.
Each T-1 ‘Pro’ can operate either as a transmitter or a receiver. Op-
eration is determined by the
MODE
button on the rear panel. You
can link two T-1 units together in alternate modes, via UTP CAT 5
cabling (using the W-DMX bus port on the rear panel), to operate
as repeaters to extend the operational distance. The front panel
TX and RX indicators show the current mode for each T-1 unit.
Operation as transmitter
Please see page 4 for details.
Operation as receiver
Please see page 8 for details.
W-DMX
made in sweden
Level
Radio
Batt
Wireless Solution
Sweden AB
FUNCTION
POWER
DATA
RX
TX
CTRL
LINK
T-1
pro
RX
TX
W-DMX
made in sweden
Level
Radio
Batt
Wireless Solution
Sweden AB
FUNCTION
POWER
DATA
RX
TX
CTRL
LINK
RADIO
ON: Indicates that
Level display is show-
ing signal strength
BATT
ON: Indicates that
Level display is
showing battery
charge
FUNCTION
Operation depends
upon current op-
eration mode - see
page 4 or page 7
for details
Level
Provides alternate indications
of radio signal strength and battery charge
every two seconds. The RADIO and BATT
indicators confirm which function is currently
being shown.
DATA
ON: Transmitting/
receiving DMX data
TX/RX
Indicate current
operation mode
CTRL
ON: Indicates that W-DMX
bus link is active
POWER
OFF: Off or using battery
ON: External power input
FLASH: Charging battery
LINK
ON: Normal operation
FLASH: Unlinking all receivers
RAPID FLASH: Linking with receivers
OFF: Not linked to a transmitter
ON: Linked to a transmitter
RAPID FLASH: Linking to a transmitter
TX MODE
RX MODE
BlackBox
T-1 Pro
Transceiver
