manualshive.com logo in svg

WinSystems SYS-405, Product Manual, Page: 43 / 57

Share
Download
WinSystems SYS-405 Product Manual Download Page 43

SYS-405/BIOS Settings

v1.0

www.winsystems.com

Page 39

Uncore Configuration

GOP Driver

Enable or disable the GOP Driver. Enabling will unload VBIOS; Disabling will load 

VBIOS.

Default Setting/Value: Enable

Integrated Graphics Device

Enables or disables the Integrated Graphics Device (IGD).

Default Setting/Value: Enable

Primary Display

Selects which of the IGD/PCI Graphics devices should be the primary display, or select 

SG for Switchable/Hybrid GFX.

Default Setting/Value: Auto

RC6 (Render Standby)

Enables or disables render standby support.

Default Setting/Value: Enable

PAVC

Enables or disables protected audio/video control.

Default Setting/Value: Lite Mode

GTT Size

Selects the GTT size.

Default Setting/Value: 2 MB

Aperture Size

Selects the aperture size.

Default Setting/Value: 256 MB

DVMT Pre-Allocated

Selects the DVMT 5.0 pre-allocated (Fixed) graphics memory size used by the internal 

graphics device.

Default Setting/Value: 64 MB

IGD Turbo

Selects the IGD Turbo feature, if Auto is selected. IGD Turbo will only be enabled when 

SOC stepping is 80 or above.

Summary of Contents for SYS-405


























































Reviews:

No comments