background image

 

 

 

Care of the tip 
 

The tip supplied is iron plated copper. If used properly, i twill last a long time.  
1. Always keep tips tinned before switching off or storing for any period of time; wipe only 
before use.  
2. Do not keep  the iron set at  high  temperature for a long period of  time as this will  break 
down the surface of the tip. 
3. Never clean the tip with coarse abrasive materials of files. 
4. If an oxide film does form it can be cleaned  by  lightly rubbing with a 600-800 grit emery 
cloth.  Isopropyl  alcohol or equivalent  and  then  immediately  recheat and  te  –  tin  the  tip  to 
prevent oxidation of the wettable surface. 
5.  Remove  the  tip  and  clean  every  twenty  hours  of  use  or  at  least  once  a  week  and 
remove any loose build up in the barrel. 
6. Do not use fluxes containing chloride or acid. Use only rosin or activated resin fluxes.. 
7. Do not use any compound or anti – seize materials on the wettable surface. 

 
Maintenance 
 
Tip replacement and dressing

 

Note: Tip  replacement  or  cleaning  should  be  done  when  the  iron  is at room  temperature. 
The  tip  can  be  changed  or  replaced  simply  by  unscrewing  the  knurled  unit  barrel 
assembly.  The  station  must  be  switched  off  and  allowed  to  cool  before  and  during  this 
operation  as  damage  may  result  if  the  system  is  left  on  without  the  tip  inserted.  After 
removing  tip, blow out any oxide dust  that  may  have formed in the tip retaining area of the 
barrel.  Be  careful  to  avoid  getting  dust  in  your  eyes.  Replace  the  tip  and  screw  the 
retaining  knurled  nut  barrel  assembly  using  only  hand  pressure  to  tighten.  Pilers  should 
only  be  used  to  tighten  the  nut  if  loosening  should  occur  when  the  iron  is  hot  to  avoid 
burning  your  fingers.  Care  should  be  taken  not  to  overtighten  as  this  would  damage  the 
element.  
 

General cleaning

  

The outer case of the iron or station may be cleaned with a damp cloth using small amount 
of liquid detergent. Never submerse the unit in liquid or allow any liquid to enter the case of 
the station. Never use solvent to clean the case. 

 

 

Melchioni S.p.A. 

Via P. Colletta, 37 
20135 MILANO – Italy 
Tel. +39 02 5794384 – Fax +39 02 5794320 
www.melchioni.it

 

 

Summary of Contents for WS-929A

















Reviews: