Winkhaus STV AV2 Page 26 Operating Manual Download

Page: 26 / 40

Page 26

Winkhaus STV

Oper

ating Manual EA

V 0124653 0505

Subject to technical changes

Winkhaus STV GmbH & Co. KG · Berkeser Str. 6 · D-98617 Meiningen · Germany · www.winkhaus.de · [email protected]

Action

Acoustic Signal

Result

Pass all the transponders

to be tutored in succession

over the antenna

for about 1 second

transponders

“tutored”

Action

Acoustic Signal

Result

Pass all the transponders

to be tutored in succession

over the antenna

no acoustic signal

(no more transponders can

be tutored)

memory over

(250 transponders have

already been programmed)

Delete mode

•

Delete-all card: Delete mode “All transponders“



Deletes all transponders

(key tags)

Gesamt

Lösch-Karte

CAUTION!

By using the delete-all card all the transponders stored in the

system will be deleted!

The action of deleting all transponders is irrevocable once the

process has been completed!

You have to teach up to 250 new transponders from the start!

The programming cards cannot open the door!

Action

Acoustic Signal

Result

Pass the delete-all card

over the antenna

for about 1 second

end of delete mode

“All transponders”

4. Operation/Programming

Summary of Contents for AV2









































Search results

Summary of Contents for AV2

Reviews:

Related manuals for AV2

Brands by name

Popular brands

Winkhaus STV AV2, Operating Manual

Search results

Summary of Contents for AV2

Reviews:

Related manuals for AV2

Brands by name

Popular brands